Changes for page LSS Firmware

Last modified by Eric Nantel on 2024/11/21 07:18

From version < 13.1 >
edited by Eric Nantel
on 2021/09/20 08:11
To version < 15.1 >
edited by Eric Nantel
on 2021/09/20 08:20
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -37,6 +37,20 @@
37 37  ** Improved LED patterns for clarity.
38 38  ** ID is now kept during a firmware update.
39 39  
40 +== Version 368 ==
41 +
42 +Released 2020-04-07
43 +
44 +Many bug fixers and new features!
45 +
46 +* QF now reports more details on version number (QF, QF1, QF2, QF3)
47 +* Maximum motor duty cycle can be controlled using MMD, QMMD (min25%, max100% = 1023).
48 +** Can set it asymmetrical by passing 2 values separated by a comma (pos limit, neg limit).
49 +* Motion filter was added for EM0.
50 +** Can be controlled with FPC, CFPC, QFPC.
51 +* IPMS system was added for EM0.
52 +** Controlled with IPE and QIPE
53 +
40 40  == Version 369 (EXPERIMENTAL) ==
41 41  
42 42  Released 2021-06-18
... ... @@ -53,12 +53,12 @@
53 53  * Backwards compatibility is a priority. This firmware shouldn't affect existing code, please report any issues. Include a reproductible command sequence if possible.
54 54  * Allows multiple commands to be sent and received as a group
55 55  * Group commands can include multiple servos without bus conflict/contention
56 -** Ex. #0QD#5QD#10QD\r - queries 3 servos at once for position
57 -** #0QD0QC0#5QD0QC0 - queries 2 servos at once for position and current (milliamps). 0 required to separate commands QD and QC
70 +** Ex. #0QD#5QD#10QD\r  -  queries 3 servos at once for position
71 +** #0QD0QC0#5QD0QC0  -  queries 2 servos at once for position and current (milliamps). 0 required to separate commands QD and QC
58 58  * Increase in supported baud rates up to 921k (adds 500k, 750k, 921.6k) with 2 and 3Mbit coming soon
59 59  * Auto baud rate (ABR) can be enabled (off by default):
60 -** Ex. #254ABR1 - Enable baudrate detection on first byte received after power-up.
61 -** #254ABR2,30 - Enable baudrate detection on first byte received after power-up. If no data for 30 seconds enable detection again on next byte.
74 +** Ex. #254ABR1  -  Enable baudrate detection on first byte received after power-up.
75 +** #254ABR2,30  -  Enable baudrate detection on first byte received after power-up. If no data for 30 seconds enable detection again on next byte.
62 62  ** Warning: ABR doesn't work well with LSS Config at the moment, updated LSS Config coming soon.
63 63  * Using #254QID120 can scan the entire bus at once for servos without conflict.
64 64  ** Servos will use a simple formula to delay their response: 200usec + <id> * 120usec, where <id> is their servo ID 0 to 253.
... ... @@ -67,11 +67,11 @@
67 67  * Configure a slot# for each servo and using (ex.) #254QD can query all servos at once without conflict
68 68  ** Ex. We have 3 servos at ID 0, 5, and 10. We want to configure them to be slots 0, 1, and 2 respectively.
69 69  *** #254SLOTCOUNT3\r - configure 3 slots on our bus
70 -*** #0SLOT0\r - we don't really have to do this one, servos default to slot 0 on power-up
71 -*** #5SLOT1\r - Servo ID5 to slot 1
72 -*** #10SLOT2\r - Servo ID10 to slot 2
73 -*** #254QD\r - Query all servos for position
74 -*** #254QD0QC0\r - Query all servos for position and current (milliamps)
84 +*** #0SLOT0\r  -  we don't really have to do this one, servos default to slot 0 on power-up
85 +*** #5SLOT1\r  -  Servo ID5 to slot 1
86 +*** #10SLOT2\r  -  Servo ID10 to slot 2
87 +*** #254QD\r  -  Query all servos for position
88 +*** #254QD0QC0\r  -  Query all servos for position and current (milliamps)
75 75  ** Note: You only need to configure slots once on power-up, #254<cmd> will offset all servo replies based on slot# after this is set.
76 76  ** Note: Why not just use servo ID as slot#? Many LSS bus setups are not using sequential IDs so it's more efficient to assign slot# then expect everyone to change their robot's logical servo IDs to be sequential.
77 77  * Fixed memory leak in MMD command
Copyright RobotShop 2018