Changes for page LSS Mechanical
Last modified by Eric Nantel on 2024/07/12 11:24
Change comment: Deleted image "LSS-Dimensions-01.png"
Summary
-
Page properties (2 modified, 0 added, 0 removed)
-
Attachments (0 modified, 2 added, 6 removed)
Details
- Page properties
-
- Author
-
... ... @@ -1,1 +1,1 @@ 1 -xwiki:XWiki. CBenson1 +xwiki:XWiki.ENantel - Content
-
... ... @@ -1,5 +1,5 @@ 1 1 (% class="wikigeneratedid" id="HTableofContents" %) 2 -** TableofContents**2 +**Page Contents** 3 3 4 4 {{toc depth="3"/}} 5 5 ... ... @@ -6,24 +6,14 @@ 6 6 = LSS Features = 7 7 8 8 |(% colspan="2" style="width:350px" %)((( 9 -== Driving Horn == 10 -))) 11 -|(% style="width:350px" %)[[image:LSS - driven horn.png]]|The aluminum driving horn is connected to the output shaft of the final gear in the gear train which is located within the servo. This output shaft has a specific cross section called a “spline” (specifically the “male” version of the spline), and the driving horn has the mating “female” spline. The details of the spline are found below. The driving horn is held in place using an M3 x 8mm pan head machine screw and has the SES standard mounting pattern described below. 12 -|(% colspan="2" style="width:350px" %)((( 13 13 == Spline == 14 14 ))) 15 15 |(% style="width:350px" %)[[image:LSS - Splines.png||width="400"]]|((( 16 -The spline allows the driv en12 +The spline allows the driving horn to be connected to the output shaft so that it rotates with the shaft. The 24 tooth spline selected is used by other servo manufacturers (for example Hitec's HS-422 and HS-645MG RC servos) and as such there are a variety of accessories / horns which are compatible and can be installed on the servo. Alternatives to using the Lynxmotion driving horn include a wheel, a pulley or sprocket, a tubing connector, specific RC horns and more. Note that there are many different spline cross sections, and in order to ensure the a horn can fit onto the output shaft of the servo, it must have the matching / identical spline. 17 17 18 18 Although the final gear which (located within the servo) which is connected to the output spline is supported by two radial ball bearings, the output spline is intended to withstand torque as opposed to radial or axial loads. 19 -))) 20 -|(% colspan="2" style="width:350px" %)((( 21 -== Idler Horn == 22 -))) 23 -|(% style="width:350px" %)[[image:LSS - idler.png||width="400"]]|((( 24 -The idler horn is not connected to the output spline and is therefore not driven. It is intended to act as a solid free-spinning connection point and can be installed in one of three locations on the servo. Installing the idler horn on the underside of the servo (as shown in the image), in line with the driving output shaft allows a Lynxmotion C-bracket to be used. 25 25 26 - Theidlerhornsub-assembly consistsofaspacer,a3mm ID x 8mm OD flanged ball bearing(Lynxmotionstandard) and the idler hornitself. The idlerhornis heldinplaceusing an M3 x 10mm pan headmachinescrew. Documentationinthiswikireferringto the "idler horn" normally refersto theidler hornassembly.16 +Learn more about [[SES - Gearing & Horns>>doc:Servo Erector Set (SES) Building System.SES - Parts.SES - Gearing Information.WebHome]] 27 27 ))) 28 28 |(% colspan="2" style="width:350px" %)((( 29 29 == Case == ... ... @@ -68,7 +68,5 @@ 68 68 69 69 = Dimensions = 70 70 71 -|(% style="width:350px" %)[[image:LSS-Dimensions-01.png]]| 72 -|[[image:LSS-Dimensions-02.png]]| 73 - 74 - 61 +(% style="width:700px" %) 62 +|(% style="width:350px" %){{lightbox image="LSS-All-Dimensions.png"/}}|{{lightbox image="LSS-Front-Dimensions.png"/}}
- LSS - Top & Bottom.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -79.0 KB - Content
- LSS - driven horn.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -54.7 KB - Content
- LSS - idler.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -64.8 KB - Content
- LSS-Dimensions-01.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.ENantel - Size
-
... ... @@ -1,1 +1,0 @@ 1 -31.2 KB - Content
- SES-V2 - SES Pattern (4).png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -20.0 KB - Content
- SES-V2 - SES Pattern (8).png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -xwiki:XWiki.CBenson - Size
-
... ... @@ -1,1 +1,0 @@ 1 -22.1 KB - Content
- LSS-All-Dimensions.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +226.2 KB - Content
- LSS-Front-Dimensions.png
-
- Author
-
... ... @@ -1,0 +1,1 @@ 1 +xwiki:XWiki.ENantel - Size
-
... ... @@ -1,0 +1,1 @@ 1 +115.7 KB - Content