Changes for page LSS Mechanical

Last modified by Eric Nantel on 2024/07/12 11:24
From version < 46.1 >
edited by Coleman Benson
on 2019/02/19 12:06
To version < 52.1 >
edited by Eric Nantel
on 2019/02/21 09:47
< >
Change comment: Upload new image "LSS-All-Dimensions.png", version 1.1

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -xwiki:XWiki.CBenson
1 +xwiki:XWiki.ENantel
Content
... ... @@ -1,5 +1,5 @@
1 1  (% class="wikigeneratedid" id="HTableofContents" %)
2 -**Table of Contents**
2 +**Page Contents**
3 3  
4 4  {{toc depth="3"/}}
5 5  
... ... @@ -9,11 +9,11 @@
9 9  == Spline ==
10 10  )))
11 11  |(% style="width:350px" %)[[image:LSS - Splines.png||width="400"]]|(((
12 -The spline allows the driven horn to be connected to the output shaft so that it rotates with the shaft. The spline selected is used by other servo manufacturers and as such there are a variety of accessories / horns which are compatible and can be installed on the servo. Alternatives to using the Lynxmotion driving horn include a wheel, a pulley or sprocket, a tubing connector, specific RC horns and more. Note that there are many different spline cross sections, and in order to ensure the a horn can fit onto the output shaft of the servo, it must have the matching / identical spline.
12 +The spline allows the driving horn to be connected to the output shaft so that it rotates with the shaft. The 24 tooth spline selected is used by other servo manufacturers (for example Hitec's HS-422 and HS-645MG RC servos) and as such there are a variety of accessories / horns which are compatible and can be installed on the servo. Alternatives to using the Lynxmotion driving horn include a wheel, a pulley or sprocket, a tubing connector, specific RC horns and more. Note that there are many different spline cross sections, and in order to ensure the a horn can fit onto the output shaft of the servo, it must have the matching / identical spline.
13 13  
14 14  Although the final gear which (located within the servo) which is connected to the output spline is supported by two radial ball bearings, the output spline is intended to withstand torque as opposed to radial or axial loads.
15 15  
16 -Learn more about SES Gearing & Horns
16 +Learn more about [[SES - Gearing & Horns>>doc:Servo Erector Set (SES) Building System.SES - Parts.SES - Gearing Information.WebHome]]
17 17  )))
18 18  |(% colspan="2" style="width:350px" %)(((
19 19  == Case ==
... ... @@ -58,7 +58,5 @@
58 58  
59 59  = Dimensions =
60 60  
61 -|(% style="width:350px" %)[[image:LSS-Dimensions-01.png]]|
62 -|[[image:LSS-Dimensions-02.png]]|
63 -
64 -
61 +|(% style="width:350px" %)[[image:LSS-Front-Dimensions.png]]|
62 +| |
LSS-All-Dimensions.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +226.2 KB
Content
LSS-Front-Dimensions.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +115.7 KB
Content

Navigation

Copyright RobotShop 2018