Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -71,7 +71,7 @@
71	71	The following table shows the suggested connection points for each of the ESCs' power leads(positive and negative), their corresponding RC 3 pin connector and input signal pin based on the copter type :
72	72
73	73	(% style="text-align:center" %)
74		-|(% style="width:400px" %) |(% style="width:50px" %) |[[image:QUADX.png||alt="HEX.jpg"]]|[[image:Y4.png||alt="HEX.jpg"]]|[[image:Y6.png||alt="HEX.jpg"]]|[[image:HEX.png||alt="HEX.jpg"]]|[[image:X8.png||alt="HEX.jpg"]]|[[image:OCTO.png||alt="HEX.jpg"]]
	74	+|(% style="width:350px" %) |(% style="width:50px" %) |[[image:QUADX.png||alt="HEX.jpg"]]|[[image:Y4.png||alt="HEX.jpg"]]|[[image:Y6.png||alt="HEX.jpg"]]|[[image:HEX.png||alt="HEX.jpg"]]|[[image:X8.png||alt="HEX.jpg"]]|[[image:OCTO.png||alt="HEX.jpg"]]
75	75	|(% colspan="1" rowspan="8" %)(((
76	76	(% style="text-align:center" %)
77	77	[[image:MES-PDB-Wiring-Shaded.png||alt="MES-PDB-Groups-Shaded.png" width="350"]]
...	...	@@ -90,7 +90,7 @@
90	90
91	91	The MES PDB has three jumpers : JA, JB and Vout. The functionality of each jumper is explained below :
92	92
93		-|(% colspan="1" rowspan="3" style="width:400px" %)(((
	93	+|(% colspan="1" rowspan="3" style="width:350px" %)(((
94	94	(% style="text-align:center" %)
95	95	[[image:MES-PDB-Top-Jumpers-Shaded.png||alt="MES-PDB-Groups.png" width="350"]]
96	96	)))|(% style="width:50px" %)(((
...	...	@@ -140,7 +140,7 @@
140	140
141	141	The MES PDB has 3 pins broken-out : BAT / Vin (Red), GND (Black) and 5V (Green) as indicated in the image below. The pinout is used to solder an optional, external 5V regulator (**not included**). Be sure to remove the JB jumper if an external 5V regulator is soldered to the PDB. Additional information regarding the optional Lynxmotion 5V and 12V regulators are provided here {//coming soon//}.
142	142
143		-|(% rowspan="3" style="width:400px" %)(((
	143	+|(% rowspan="3" style="width:350px" %)(((
144	144	(% style="text-align:center" %)
145	145	[[image:MES-PDB-External5V-Shaded.png||width="350"]]
146	146
...	...	@@ -168,7 +168,7 @@
168	168
169	169	Although the MES PDB is intended to be used with any flight controller copter system, it was designed to be directly interfaced with the Lynxmotion Quadrino Nano Flight Controller.
170	170
171		-|(% style="width:400px" %)(((
	171	+|(% style="width:350px" %)(((
172	172	(% style="text-align:center" %)
173	173	[[image:MES-PDB-Quadrino-Wiring.png||height="350" width="350"]]
174	174	)))|(((
...	...	@@ -200,9 +200,8 @@
200	200
201	201	= Dimensions =
202	202
203		-The suggested mounting method for the PDB is using either standoffs or double-sided tape. Ensure there are no loose wires or connections which can contact the PDB and potentially cause a short circuit.
	203	+|(% style="width:350px" %)[[image:MES-PDB-Dimensions.png]]|The suggested mounting method for the PDB is using either standoffs or double-sided tape. Ensure there are no loose wires or connections which can contact the PDB and potentially cause a short circuit.
204	204
205		-[[image:MES-PDB-Dimensions.png||width="400"]]
206	206
207	207	= Safety =
208	208