Changes for page A4WD3-LED Board
Last modified by Eric Nantel on 2022/08/30 08:56
Change comment: There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,0 +1,67 @@ 1 +{{lightbox image="LSS-LED.png" width="350"/}} 2 + 3 +[[[[image:[email protected]||alt="buy-online.jpg"]]>>https://www.robotshop.com/en/lynxmotion-lss-led-module-12v-lithium-batteries-or-lss.html||rel="noopener noreferrer" target="_blank"]] 4 + 5 +**Table of Contents** 6 + 7 +{{toc/}} 8 + 9 += Description = 10 + 11 +The Lynxmotion (LSS) - LED module is intended to add lighting to your servo erector set (SES) v2 project. The module is meant to be connected to the standard mounting of an Lynxmotion Smart Servo (LSS) Motor and can be added to the serial bus. Like the LSS which can be operated over a range of input voltages, this LED module is meant to operate between 6V and 12V. The module can be powered one of two ways where the onboard switch selects which of the two sources powers the LED: 12 + 13 +* Option 1: Four-pin LSS bus (Tx, GND, 12V, Rx) 14 +* Option 2: Four-pin, three cell Lithium balance port (3 individual cells = 11.1V) 15 + 16 += Features = 17 + 18 +* Bright cool white LED 19 +* On / Off switch (act as an isolator for different power input as well) 20 +* 2x LSS connectors to power the LED and transfer to the next unit in the LSS Bus. 21 +* LSS motor mounting 22 + 23 +((( 24 += Specifications = 25 + 26 +* Input Voltage: 12V Nominal (6.4V to 18V) 27 +* Connections: 28 +** LSS Connector (Molex 99990988) 29 +** Lithium balance port (JST B4B-XH-A) 30 +* LED: Everlight 37-21S (~~38 lumen white LED) 31 +* Current: ~~100 mA 32 +))) 33 + 34 +((( 35 += Pinout = 36 + 37 +|(% rowspan="10" style="text-align:center; vertical-align:middle; width:350px" %){{lightbox image="LSS-LED-PinOUt.png"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)((( 38 +**Positive LSS**: Voltage Input from the LSS connectors 39 +))) 40 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Positive Balance**: Voltage Input from the balance port 41 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Ground (0V): **All common grounds 42 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)((( 43 +**LSS Connectors:** LED will be OFF 44 + 45 +**Balance Port: **LED will be ON 46 +))) 47 +|(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Black.png"]]|(% style="vertical-align:middle" %)((( 48 +**LSS Connectors:** LED will be ON 49 + 50 +**Balance Port: **LED will be OFF 51 +))) 52 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Not Connected** 53 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Servo Rx pin (Rx)**: In serial mode, this pin should be connected to the Tx pin of a TTL serial device. 54 +|(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Servo Tx pin (Tx)**: In serial mode, this pin should be connected to the Rx pin of a TTL serial device. 55 + 56 += Wiring = 57 + 58 +(% style="width:700px" %) 59 +|(% style="text-align:center; width:350px" %)**LSS Bus**|(% style="text-align:center" %)**12V Battery (balance port)** 60 +|{{lightbox image="LSS-LED-Wiring-LSS.png"/}}|{{lightbox image="LSS-LED-Wiring-Battery.png"/}}((( 61 + 62 +))) 63 + 64 += Dimensions & Mounting = 65 + 66 +|(% style="width:300px" %){{lightbox image="LSS-LED-Dimensions.png"/}}|(% style="width:300px" %)[[image:servo-erector-set-system.ses-electronics.ses-modules.lss-2io-board.WebHome@LSS-2IO-Mounting.gif]]| 67 +)))