Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,5 +1,10 @@
	1	+|{{toc/}}|(% style="text-align:right" %)[[image:LSS-Adapter.png||queryString="width=250" width="250"]]
	2	+
	3	+
1	1	[[image:LSS-Adapter.png||queryString="width=250" width="250"]]
2	2
	6	+{{toc/}}
	7	+
3	3	= Description =
4	4
5	5	The Lynxmotion Smart Servo (LSS) Adapter Board is a simple to use interface to configure/control the Lynxmotion Smart Servos. The board also provides power distribution and includes over-current protection using re-settable 3A (5A trip) fuses for each of its six outputs. It can be powered from a battery through the on-board male XT60 connector, or with a wall adapter (using an XT60 to barrel adapter). There are many ways to interface with this board, as described below.
...	...	@@ -45,7 +45,7 @@
45	45	|(% colspan="2" style="width:350px" %)(((
46	46	= Power =
47	47	)))
48		-|(% style="width:350px" %)[[image:LSS-ADAPTER-Board-Power.png||queryString="width=350"]]|(((
	53	+|(% style="width:350px" %){{lightbox image="LSS-ADAPTER-Board-Power.png"/}}|(((
49	49	//__~*~** Power the Board ~*~**__//
50	50
51	51	The FTDI chip can be powered through the on-board USB or with an external power supply through the XT60 connector. The 5V from the USB will only power the FTDI chip and the XBee compatible wireless module (if inserted) and won't power the servos. To power the servos, an external power supply (6V to 12V) is needed (more information in the "LSS - Electrical" section). If both USB and external power supply are connected at the same time, the external power supply will be automatically selected to power the FTDI chip and XBee module if it's higher than 7V. The external power supply can be a battery or an AC-to-DC wall adapter with the appropriate barrel to XT60 converter (more information in "[[LSS - Electrical>>doc:Lynxmotion Smart Servo (LSS).LSS - Electrical.WebHome||title="LSS Electrical"]]" section).
...	...	@@ -61,7 +61,7 @@
61	61	(1) : XT60 Connector for 6V-12V external power input (more information in "LSS - Electrical" section).
62	62	(2) : LSS servo connectors
63	63	)))
64		-|(% style="width:350px" %)[[image:LSS-ADAPTER-Servo-Power.png||queryString="width=350"]]|__//~*~** Power the Servos ~*~**//__
	69	+|(% style="width:350px" %){{lightbox image="LSS-ADAPTER-Servo-Power.png"/}}|__//~*~** Power the Servos ~*~**//__
65	65	|(% colspan="2" style="width:350px" %)
66	66
67	67	= Configurations =
...	...	@@ -73,7 +73,7 @@
73	73	|(% colspan="2" style="width:300px" %)(((
74	74	== Arduino ==
75	75	)))
76		-|(% style="width:300px" %)[[image:LSS-ADAPTER-Arduino.png||queryString="width=350"]]|(((
	81	+|(% style="width:300px" %){{lightbox image="LSS-ADAPTER-Arduino.png"/}}|(((
77	77	== ==
78	78
79	79	To use the LSS Adapter Board with an Arduino Board, the switch should be on **position 1**.
...	...	@@ -94,6 +94,10 @@
94	94	1 x 8 positions 0.1" (2.54mm) pitch 16mm (or higher) contact length header receptacle connectors.
95	95	)))
96	96	|(% colspan="2" style="width:300px" %)(((
	102	+== Raspberry Pi ==
	103	+)))
	104	+|(% style="width:300px" %)Pi Image|
	105	+|(% colspan="2" style="width:300px" %)(((
97	97	== XBee / Bluetooth Bee / WiFi Bee / RF Bee ==
98	98	)))
99	99	|(% style="width:300px" %)[[image:LSS Adapter - XBee Standard.png||queryString="width=350" alt="LSS Adapter - XBee Standard.jpg" width="350"]]|(((