Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.BDaouas
	1	+xwiki:XWiki.CBenson

Content

...	...	@@ -1,17 +1,18 @@
1	1	[[image:LSS-ADA.png||alt="LSS-Adapter.png" width="350"]]
	2	+**Table of Contents**
2	2
3	3	{{toc/}}
4	4
5	5	= Description =
6	6
7		-The Lynxmotion Smart Servo (LSS) Adapter Board is an electronic board which allows for easy configuration and control of the Lynxmotion Smart Servos. The board includes a variety of features and functionality and provides power distribution via six LSS six connectors. The board is intended to be powered from a LiPo battery through the on-board male XT60 connector, or with a wall adapter with a female XT60 connector. There are many ways to interface with this board, as described below.
	8	+The Lynxmotion Smart Servo (LSS) Adapter Board is an electronic board which allows for easy connection to and control of the Lynxmotion Smart Servos. The board includes a variety of features and functionality and provides power distribution via six LSS connectors. The board is ideally intended to be powered from a LiPo battery through the on-board male XT60 connector, or with a wall adapter equipped with a female XT60 connector. There are many ways to interface with this board, as described below.
8	8
9	9	= Features =
10	10
11		-* Control LSS actuators via 6x connectors (4-pins Molex)
12		-* On-board XBee Socket
13		-* Can work as an XBee explorer USB board
14		-* Arduino stackable shield compatible
	12	+* Connect to and control LSS actuators via 6x connectors
	13	+* On-board Bee Socket (XBee, Bluetooth Bee WiFi Bee modules)
	14	+* Can function as a USB XBee explorer board
	15	+* Arduino shield compatible using stacking headers
15	15	* Selectable control method : USB, Arduino or XBee
16	16	* Raspberry Pi B+/2/3 mounting compatibility
17	17	* XT60 Connector for power input
...	...	@@ -19,19 +19,19 @@
19	19
20	20	= Specifications =
21	21
22		-* 3A (max) continuous current per channel
	23	+* Continuous current per connector: 3A (max)
23	23	* Built-in USB to serial (FTDI Virtual COM Port chip)
24	24	* Built-in 5V regulator
25	25	* Built-in 3.3V regulator
26	26	* USB Mini connector
27		-* Dimensions : 64 x 64 x 15mm
28		-* Mounting holes diameter : 3.1mm
	28	+* Dimensions: 64 x 64 x 15mm
	29	+* Mounting hole diameter: 3.1mm
29	29
30	30	(((
31	31	= Communication / Control =
32	32
33	33	* Mini USB: ex: computer, laptop, Raspberry Pi
34		-* Arduino shield compatible
	35	+* Arduino shield compatible (using M/M or extended M/F headers)
35	35	* TTL UART Microcontroller or FPGA control (5V) via Tx, Rx, GND pins
36	36	* Wireless module with XBee footprint (Bluetooth Bee, WiFi Bee etc.)
37	37	)))
...	...	@@ -42,10 +42,10 @@
42	42
43	43	= Pinout =
44	44
45		-|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-ADAPTER-PinOut.png"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|
46		-|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|
47		-|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|
48		-|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|
	46	+|(% rowspan="4" style="width:350px" %){{lightbox image="LSS-ADAPTER-PinOut.png"/}}|(% style="text-align:center; vertical-align:middle; width:35px" %)[[image:Lyxnmotion [email protected]]]|**Servo Vcc pin**: Refer to the Voltage section of the LSS - Specifications page to understand which voltages are meant to be connected to this pin.
	47	+|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Ground (GND)**: This pin should be connected to both the communication sources' ground, as well as that of the power source (principle of "common ground").
	48	+|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Rx pin**: In serial mode, this pin should be connected to a 5V TTL serial pin. In RC mode, the pin should be connected to an 5V RC PWM pin
	49	+|(% style="text-align:center; vertical-align:middle" %)[[image:Lyxnmotion [email protected]]]|**Servo Tx pin**: In serial mode, this pin sends the output from query commands. In RC mode, the cable does not need to be connected as there is no output.
49	49
50	50	|(% colspan="2" style="width:350px" %)(((
51	51	= Wiring =