Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -143,7 +143,6 @@
143	143	| |[[**A**ngular **A**cceleration>>||anchor="HAngularAcceleration"]]|(% style="text-align:center" %)AA|(% style="text-align:center" %)QAA|(% style="text-align:center" %)CAA|(% style="text-align:center" %) |(% style="text-align:center" %)0.01°/s^2|
144	144	| |[[**A**ngular **D**eceleration>>||anchor="HAngularDeceleration"]]|(% style="text-align:center" %)AD|(% style="text-align:center" %)QAD|(% style="text-align:center" %)CAD|(% style="text-align:center" %) |(% style="text-align:center" %)0.01°/s^2|
145	145	| |[[**G**yre Direction>>||anchor="HGyreDirection"]]|(% style="text-align:center" %)G|(% style="text-align:center" %)QG|(% style="text-align:center" %)CG|(% style="text-align:center" %)1|(% style="text-align:center" %)1 or -1|Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)
146		-| |[[**F**irst Position (**D**eg)>>||anchor="HFirstPosition"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QFD|(% style="text-align:center" %)CFD|(% style="text-align:center" %) |(% style="text-align:center" %)0.01°|Reset required after change.
147	147	| |[[Maximum **S**peed in **D**egrees>>||anchor="HMaximumSpeedinDegrees"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %)QSD|(% style="text-align:center" %)CSD|(% style="text-align:center" %) |(% style="text-align:center" %)0.01°/s|SD / CSD overwrites SR / CSR
148	148	| |[[Maximum **S**peed in **R**PM>>||anchor="HMaximumSpeedinRPM"]]|(% style="text-align:center" %)SR|(% style="text-align:center" %)QSR|(% style="text-align:center" %)CSR|(% style="text-align:center" %) |(% style="text-align:center" %)RPM|SR / CSR overwrites SD / CSD
149	149
...	...	@@ -556,25 +556,6 @@
556	556	)))
557	557
558	558	|(% colspan="2" %)(((
559		-====== __First Position__ ======
560		-)))
561		-|(% style="width:30px" %) |(((
562		-In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned.
563		-
564		-Note that the number should be restricted to -1790 (-179.0 degrees) to +1790 (179.0 degrees) and values beyond this will be changed to 1800.
565		-
566		-Query First Position in Degrees (**QFD**)
567		-
568		-Ex: #5QFD<cr> might return *5QFD900<cr>The reply above indicates that servo with ID 5 has a first position of 90.0 degrees. If there is no first position value stored, the reply will be DIS.
569		-
570		-Configure First Position in Degrees (**CFD**)
571		-
572		-Ex: #5CFD900<cr>
573		-
574		-This configuration command means the servo, when set to smart mode, will immediately move to 90.0 degrees upon power up. Sending a CFD command without a number (Ex. #5CFD<cr>) results in the servo remaining limp upon power up. In order to remove the first position, send no value, ex: #5CFD<cr>
575		-)))
576		-
577		-|(% colspan="2" %)(((
578	578	====== __Maximum Speed in Degrees__ ======
579	579	)))
580	580	|(% style="width:30px" %) |(((