Summary

• Page properties (1 modified, 0 added, 0 removed)
• Attachments (0 modified, 2 added, 0 removed)
  • LSS-P-ID-Config-COM.png
  • LSS-P-ID-Config-Open.png

Details

Page properties

Content

...	...	@@ -1,23 +1,44 @@
1		-
	1	+= Step 1 - Connections =
2	2
	3	+__Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__
3	3
4		-|(% colspan="2" %)Step 1
5		-|(% style="width:30px" %) |While your power supply is OFF (important) connect the Servo power and USB cables
6		-|(% colspan="2" %)Step 2
7		-| |Power up your supply
8		-|(% colspan="2" %)
9		-| |Open the LSS PRO Configuration software (HERE)
10		-|(% colspan="2" %)
11		-| |Select the COM port associated with your actuator & connect
12		-|(% colspan="2" %)
13		-| |Select your actuator from the drop-down list
14		-|(% colspan="2" %)
15		-| |Select the CID configuration command in the list
16		-|(% colspan="2" %)
17		-| |Set the desired ID in the text box
18		-|(% colspan="2" %)
19		-| |Send your command
20		-|(% colspan="2" %)
21		-| |Reset your actuator
	5	+* (((
	6	+Connect the XT60 from your power supply
	7	+)))
	8	+* Connect the USB Type-C cable
22	22
23		-
	10	+= Step 2 - Power-Up =
	11	+
	12	+* Proceed with powering the actuator
	13	+
	14	+= Step 3 - Software =
	15	+
	16	+* Install the LSS PRO Configuration software ([[HERE>>doc:ses-pro.lss-pro.lss-p-configuration-software.WebHome]])
	17	+* Open the LSS PRO Configuration software
	18	+
	19	+[[image:LSS-P-ID-Config-Open.png]]
	20	+
	21	+= Step 4 - Connection =
	22	+
	23	+* Select the COM port associated with your actuator
	24	+* Click Connect
	25	+
	26	+[[image:LSS-P-ID-Config-COM.png]]
	27	+
	28	+= Step 5 - Selection =
	29	+
	30	+* In the drop-down menu, select your actuator
	31	+
	32	+= Step 6 - Set the ID =
	33	+
	34	+* In the "Configuration" drop-down menu, select "CID / ID Number"
	35	+* In the text entry box, set the desired ID number
	36	+* Click on the "Send" button
	37	+* The "RESET" button will start blinking, click on it to reset
	38	+
	39	+= Step 7 - Confirm =
	40	+
	41	+* The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4
	42	+* Verify that your ID is not what you have set it at
	43	+
	44	+At that point your Actuator should have the new ID configured.

LSS-P-ID-Config-COM.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+10.5 KB

Content

LSS-P-ID-Config-Open.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.ENantel

Size

...	...	@@ -1,0 +1,1 @@
	1	+178.7 KB

Content