Changes for page LSS-PRO Configure IDs

Last modified by Coleman Benson on 2024/10/08 12:52
From version < 4.1 >
edited by Eric Nantel
on 2024/07/25 11:16
To version < 27.1
edited by Coleman Benson
on 2024/10/08 12:52
<
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -xwiki:XWiki.ENantel
1 +xwiki:XWiki.CBenson
Content
... ... @@ -1,6 +1,11 @@
1 -= Step 1 - Connections =
1 +(% style="width:710px" %)
2 +|(% colspan="2" %)(((
3 +== LSS-PRO Configure IDs ==
4 +)))
5 +|(% style="width:25px" %) |(((
6 +~1. Wiring
2 2  
3 -__Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__
8 +__WARNING:**Do not hot plug the servo!** Make sure the power supply is turned OFF (and waited at least 10s for it to completely discharge its internal capacitor) before connecting it to the LSS-P actuator__
4 4  
5 5  * (((
6 6  Connect the XT60 from your power supply
... ... @@ -7,29 +7,63 @@
7 7  )))
8 8  * Connect the USB Type-C cable
9 9  
10 -= Step 2 - Power-Up =
15 +If you are using a battery, ensure there is an On/Off switch between the battery and the servo(s).
16 +)))
17 +| |(((
18 +2. Power ON
11 11  
12 -* Proceed with powering the actuator
20 +* Power the actuator (set the switch to ON)
21 +)))
22 +| |(((
23 +3. LSS PRO Config Software
13 13  
14 -= Step 3 - Software =
15 -
16 -* Install the LSS PRO Configuration software (HERE)
25 +* Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]])
17 17  * Open the LSS PRO Configuration software
18 18  
19 -= Step 4 - Connection =
28 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Open.png]]
29 +)))
30 +| |(((
31 +4. Connect to the BUS
20 20  
21 -* Select the COM port associated with your actuator
33 +* Select the COM port associated with your actuator or the first servo in the BUS
22 22  * Click Connect
23 23  
24 -= Step 5 - Selection =
36 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-COM.png]]
37 +)))
38 +| |(((
39 +5. Actuator Selection
25 25  
26 26  * In the drop-down menu, select your actuator
27 27  
28 -= Step 6 - Set the ID =
43 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Select.png]]
44 +)))
45 +| |(((
46 +6. Set the servo's ID
29 29  
30 -* In the "Configuration" drop-down menu, select "CID / ID Number"
31 -* In the text entry box, set the desired ID number
32 -* Click on the "Send" button
33 -* Click on the "Reset button
48 +* In the "Configuration" drop-down menu, select the **C**onfigure **ID** command "CID / ID Number"
34 34  
50 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-CID.png]]
51 +
52 +* In the text entry box, set the desired ID number (integers only up to 253)
53 +
54 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-ID1.png]]
55 +
56 +* Click on the "Send" button to send the command to the servo
57 +
58 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Send.png]]
59 +
60 +* The "RESET" button will start blinking, click on it to reset the servo
61 +
62 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Reset.png]]
63 +)))
64 +| |(((
65 +7. Confirm
66 +
67 +* The software will automatically re-connect to the actuator but if not, proceed as done in Step 4
68 +* Verify that your ID is not what you have set
69 +
70 +[[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-ID1-Confirm.png]]
71 +
35 35  At that point your Actuator should have the new ID configured.
73 +)))
74 +| |8. Repeat individualls for each servo in the BUS ensuring only one servo at a time is connected via its own USB to the software.
LSS-P-ID-Config-CID.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +33.9 KB
Content
LSS-P-ID-Config-COM.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +12.4 KB
Content
LSS-P-ID-Config-ID1-Confirm.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +6.6 KB
Content
LSS-P-ID-Config-ID1.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +17.4 KB
Content
LSS-P-ID-Config-Open.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +178.7 KB
Content
LSS-P-ID-Config-Reset.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +7.8 KB
Content
LSS-P-ID-Config-Select.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +6.5 KB
Content
LSS-P-ID-Config-Send.png
Author
... ... @@ -1,0 +1,1 @@
1 +xwiki:XWiki.ENantel
Size
... ... @@ -1,0 +1,1 @@
1 +17.5 KB
Content
Copyright RobotShop 2018