Wiki source code of LSS-PRO Configure IDs
Version 24.1 by Eric Nantel on 2024/09/19 13:39
Hide last authors
 |
23.1 | 1 | (% style="width:710px" %) |
| 2 | |(% colspan="2" %)((( | ||
| 3 | = LSS-PRO Configure IDs = | ||
| 4 | ))) | ||
| 5 | |(% style="width:25px" %) |((( | ||
| 6 | ~1. Wiring | ||
| |
2.2 | 7 | |
| |
4.1 | 8 | __Warning: Make sure your power supply is OFF and wait at least 10s before connecting to the LSS-P actuator.__ |
| |
2.2 | 9 | |
| |
4.1 | 10 | * ((( |
| 11 | Connect the XT60 from your power supply | ||
| 12 | ))) | ||
| 13 | * Connect the USB Type-C cable | ||
| |
23.1 | 14 | ))) |
| 15 | | |((( | ||
| 16 | 2. Power-Up | ||
| |
2.2 | 17 | |
| |
4.1 | 18 | * Proceed with powering the actuator |
| |
23.1 | 19 | ))) |
| 20 | | |((( | ||
| 21 | 3. LSS PRO Config Software | ||
| |
4.1 | 22 | |
| |
23.1 | 23 | * Install the LSS PRO Configuration software ([[HERE>>path:/info/wiki/lynxmotion/view/ses-pro/lss-pro/lss-p-configuration-software/]]) |
| |
4.1 | 24 | * Open the LSS PRO Configuration software |
| |
21.1 | 25 | |
| |
24.1 | 26 | [[image:ses-pro.lss-pro.lss-p-configuration-software.lss-p-config-configure-ids.WebHome@LSS-P-ID-Config-Open.png]] |
| |
23.1 | 27 | ))) |
| 28 | | |((( | ||
| 29 | 4. Connection | ||
| |
5.1 | 30 | |
| |
4.1 | 31 | * Select the COM port associated with your actuator |
| 32 | * Click Connect | ||
| 33 | |||
| |
22.1 | 34 | [[image:LSS-P-ID-Config-COM.png]] |
| |
23.1 | 35 | ))) |
| 36 | | |((( | ||
| 37 | 5. Actuator Selection | ||
| |
5.1 | 38 | |
| |
4.1 | 39 | * In the drop-down menu, select your actuator |
| 40 | |||
| |
22.1 | 41 | [[image:LSS-P-ID-Config-Select.png]] |
| |
23.1 | 42 | ))) |
| 43 | | |((( | ||
| 44 | 6. Set the ID | ||
| |
16.1 | 45 | |
| |
4.1 | 46 | * In the "Configuration" drop-down menu, select "CID / ID Number" |
| |
16.1 | 47 | |
| |
22.1 | 48 | [[image:LSS-P-ID-Config-CID.png]] |
| |
16.1 | 49 | |
| |
4.1 | 50 | * In the text entry box, set the desired ID number |
| |
16.1 | 51 | |
| |
22.1 | 52 | [[image:LSS-P-ID-Config-ID1.png]] |
| |
16.1 | 53 | |
| |
4.1 | 54 | * Click on the "Send" button |
| |
16.1 | 55 | |
| |
22.1 | 56 | [[image:LSS-P-ID-Config-Send.png]] |
| |
16.1 | 57 | |
| |
5.1 | 58 | * The "RESET" button will start blinking, click on it to reset |
| |
4.1 | 59 | |
| |
22.1 | 60 | [[image:LSS-P-ID-Config-Reset.png]] |
| |
23.1 | 61 | ))) |
| 62 | | |((( | ||
| 63 | 7. Confirm | ||
| |
16.1 | 64 | |
| |
5.1 | 65 | * The software will automatically re-connect to the actuator but if not you can do it manually like in Step 4 |
| 66 | * Verify that your ID is not what you have set it at | ||
| 67 | |||
| |
22.1 | 68 | [[image:LSS-P-ID-Config-ID1-Confirm.png]] |
| |
16.1 | 69 | |
| |
4.1 | 70 | At that point your Actuator should have the new ID configured. |
| |
23.1 | 71 | ))) |