Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,0 +1,34 @@
	1	+(% style="width:700px" %)
	2	+|(% colspan="2" %)
	3	+|(% style="width:350px" %)Connect the USB cable between your Arm and PC|(% colspan="1" rowspan="2" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v2-robots/ses-v2-arms/lss-4dof-arm/4dof-arm-quickstart/4dof-electronics/WebHome/SESV2-LSS-ARTICULATED-ARM-ELECTRONICS-Step-03-B.PNG?="/}}
	4	+|Connect the power adapter XT60 to your Arm
	5	+|Power on the robot with the power supply ON/OFF switch|
	6	+|Start the LSS FlowArm software|
	7	+|Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF)|
	8	+|It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200)|
	9	+|The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port.|
	10	+
	11	+= Connecting via USB =
	12	+
	13	+1. Connect the USB cable to the LSS Adapter board on your robot
	14	+1. Plug the USB connector into the PC
	15	+1. Connect your LSS to the LSS-Adapter with the Lynxmotion cable
	16	+1. Connect the power to the LSS Adapter via the yellow XT60 plug
	17	+1. Power on the robot (On/Off switch)
	18	+1. Start the LSS FlowArm software
	19	+1. Select the type of LSS Arm you are using (3 DoF / 4 DoF / 5 DoF)
	20	+1. It will automatically try to find the connected Arm but, if not, you can manually choose the appropriate COM port from the drop-down list & the baud rate (default is 115200)
	21	+1. The software sends a query to servo ID1 and once a reply is received, it determines connection has been established and a green light will be displayed aside the COM port.
	22	+
	23	+= Calibration =
	24	+
	25	+1. Go in "TEACH" mode with the button on the top bar.
	26	+1. Manually place the arm in the correct position for your model and with the gripper closed. (see images bellow)
	27	+1. Store the values or Offsets by clicking "STORE OFFSETS"
	28	+1. At that point the arm should "stay" in that position once released
	29	+1. Exit the "TEACH" mode by clicking it again
	30	+
	31	+= Calibration Positions =
	32	+
	33	+|(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**4 DoF**|(% colspan="2" rowspan="1" style="text-align:center; vertical-align:middle" %)**3 DoF **
	34	+|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||width="200"]]|(% style="text-align:center; vertical-align:middle" %)[[image:[email protected]||alt="lss-flowarm-left-3dof.png" width="200"]]