Changes for page A-Pod 3DoF Tail Assembly Instructions
Last modified by Eric Nantel on 2024/07/03 09:20
Change comment: There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
Details
- Page properties
-
- Content
-
... ... @@ -95,7 +95,7 @@ 95 95 <td valign="top" align="left" colspan="2"><font face="Verdana" size="2"> </font></td> 96 96 </tr> 97 97 <tr> 98 - <td valign="top"><p><b><font face="Verdana" size="2">Step 4.<br> 98 + <td align="left" valign="top"><p><b><font face="Verdana" size="2">Step 4.<br> 99 99 </font></b><font face="Verdana" size="2">Using four 4-40 x .250" hex socket head screws, attach four 0.75" hex spacers to the Bot Board II as shown. Insert the Basic Atom Pro 28 chip into the socket. </font></p> 100 100 <table border="0" > 101 101 <tbody><tr> ... ... @@ -136,7 +136,7 @@ 136 136 <td valign="top" align="left" colspan="2"><font face="Verdana" size="2"> </font></td> 137 137 </tr> 138 138 <tr> 139 - <td valign="top"><p><b><font face="Verdana" size="2">Step 6.<br> 139 + <td align="left" valign="top"><p><b><font face="Verdana" size="2">Step 6.<br> 140 140 </font></b><font face="Verdana" size="2"> Slide the two "T" shaped PVC pieces into the slots as shown. Attach the bottom panel using four 4-40 x .375" hex screws. </font></p> 141 141 <table border="0" > 142 142 <tbody><tr> ... ... @@ -187,7 +187,7 @@ 187 187 <td valign="top" align="left" colspan="2"><font face="Verdana" size="2"> </font></td> 188 188 </tr> 189 189 <tr> 190 - <td valign="top"><p><b><font face="Verdana" size="2">Step 9.</font></b><br> 190 + <td align="left" valign="top"><p><b><font face="Verdana" size="2">Step 9.</font></b><br> 191 191 <font face="Verdana" size="2"> Slide the tail assembly in place in the rear of the chassis. <br> 192 192 </font></p></td> 193 193 <td align="center" valign="top"><a target="_blank"><img src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-3-4-dof-hexapods/a-pod-tail/WebHome/assm09.jpg" alt="" hspace="10" border="2"></a><br> ... ... @@ -197,7 +197,7 @@ 197 197 <td valign="top" align="left" colspan="2"><br class="pb"></td> 198 198 </tr> 199 199 <tr> 200 - <td valign="top"><p><b><font face="Verdana" size="2">Step 10.</font></b><br> 200 + <td align="left" valign="top"><p><b><font face="Verdana" size="2">Step 10.</font></b><br> 201 201 <font face="Verdana" size="2"> Attach a HS-645MG of the robot using 3mm screws, washers and nuts. Connect the servo horn to the chassis using four 2-56 x .375" screws.</font></p> 202 202 <table border="0" > 203 203 <tbody><tr>