BRAT Biped SEQ Tutorial v2.01XE

<td valign="top" align="left">Biped BRAT SEQ Tutorial.

Updated 03/27/2008<!--webbot

6

bot="Timestamp" i-checksum="12626" endspan -->.

7

Safety first! Wear eye protection and never touch a powered robot!

8

Note: This tutorial applies to the SSC-32 v2 with Register Support.

9

Software:

10

- BRAT Projects

11

> <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-seq/WebHome/minibipd.zip">minibipd.zip</a></td>

12

13

Image of Biped BRAT.</td>

</tr>

<tr>

</tr>

<tr>

I. BRAT Configuration: SSC-32 Registers

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 1.

28

Download and install <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/ses-software/lynxterm/" target="_blank">LynxTerm</a>. Connect the

29

SSC-32 to the serial port and apply power. The green LED should light and stay on until it receives a valid serial command. Run the LynxTerm

30

program.

31

Step 2.

32

Type "ver" and press "enter". You should see "SSC32-V2.01XE" or higher returned. However, if you have the firmware

33

v2.01XE, there is still one more test you have to do. Due to an error on our part, the early v2.01XE firmware did not include register support,

34

and will need to be updated.

35

To test for register support on your 2.01XE firmware, click on "Reg.", then "Read", and

36

enable "Initial Pulse Offset". Click on "Write", then click "Read".

37

- If the option is still enabled, you have the proper version and can move on to Step 4.

38

- If the option is now disabled, you need to update your firmware.

</td>

Figure 2.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 3.

49

Download the 2.01XE firmware. Remove power from the

50

SSC-32, and make sure the baud rate is set to 115.2k. Refer to the manual if you need more information regarding baud rate.

51

Apply power to the SSC-32 again, make sure it's connected to the PC, and click on "Firmware" along

52

the bottom of the LynxTerm screen.

53

Click on "Open" and browse to the firmware file you just downloaded.

54

Click on "Begin Update".

</td>

Figure 3.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 4.

65

When the firmware has been successfully updated, click "Ok" then "Exit".

66

Now repeat the ver test: type "ver" then press "Enter". You should see the proper firmware

67

version returned.</td>

Figure 4.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 5.

77

Place the robot in a position as close to neutral as possible. Click on "All=1500" in the bottom right portion of the screen. Your

78

robot should go to and hold the neutral position, and should resemble figures 5-2 and 5-3. If the joints are off by more than 15° you may have

79

made an error in assembly. To correct this, remove the center screw from the round servo horn, pull the servo horn off the servo, rotate until

80

it's aligned, then reattach the servo horn.</td>

Figure 5.</td>

</tr>

<tr>

</tr>

<tr>

Figure 5-2.

</td>

Figure 5-3.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 6.

103

From the main screen, click on "Reg" to open the Registers page.

104

Click on "Default" to initialize default values.</td>

Figure 6.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 7.

114

You'll want to start with the robot's right hip. Select servo #2, then adjust the "Offset" slider until the joint is a perfect 90°

115

angle.

116

Note, the mouse's scrollwheel or keyboard's arrow keys can be used to make fine adjustments.

</td>

Figure 7.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 8.

127

Now adjust the robot's right knee servo. Select servo #1, then adjust the "Offset" slider until the robot's leg is perpendicular to

the ground.</td>

Figure 8.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 9.

139

Now adjust the robot's right ankle servo. Select servo #0, then adjust the "Offset" slider until the robot's foot is perpendicular to

140

the leg.

141

Do the same for the robot's left side (servos 16, 17, and 18).</td>

Figure 9.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 10.

151

Click "Write" and exit LynxTerm when the write process is finished.

152

Note, you can also check "Initial Pulse Width" to automatically enable the servos on power-up as an

153

option. If you do, make sure you "Write" to save the changes. The next section of this tutorial allows Sequencer to enable the servos

154

instead.

155

This completes the BRAT configuration process for the SSC-32 registers. Now, whenever the robot is turned on,

156

the servos will automatically be aligned and/or enabled.

</td>

Figure 10.</td>

</tr>

<tr>

</td>

</tr>

<tr>

II. BRAT Configuration: Sequencer

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 1.

176

Install the SSC-32 Visual Sequencer. Read the Sequencer's manual. This tutorial is not meant to replace the manual! Run the Visual Sequencer

177

program.

178

Click on "SSC-32" in the upper left corner. This process configures the software to the servos in

179

your robotic assembly. To do this, the servos' min and max positions are defined and the actual angles each joint can achieve are entered.

180

Take time to do an accurate configuration! Your robot will only perform as well as the accuracy of the

181

configuration file it's using. In other words, sloppy configuration will make a sloppy robot when sharing projects.

</td>

Figure 1.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 2.

192

Each servo you configure must first be enabled. You simply click on the Enable checkbox. You can move the servo by adjusting the slider bar.

193

You will enable the servos one at a time as you configure them.

</td>

Figure 2.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 3.

204

Move the slider for servo 0 until the servo is at a 45° angle as shown.

205

Right click on the slider and select "Set position as min" from the menu as shown in Figure 3-2.

206

Adjust the "Min Deg" box to say "-45°" as shown in Figure 3-3.

</td>

Figure 3-1.</td>

</tr>

<tr>

</td>

</tr>

<tr>

Figure 3-2.

</td>

Figure 3-3.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 4.

230

Move the slider for servo 0 until the servo is at an 84° angle as shown.

231

Right click on the slider and select "Set position as max" from the menu as shown in Figure 4-2.

232

Adjust the "Max Deg" box to say "84°" as shown in Figure 4-3.

233

Move the slider back to 0° before going on to the next servo.

</td>

Figure 4-1.</td>

</tr>

<tr>

</tr>

<tr>

Figure 4-2.

</td>

Figure 4-3.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step 5.

257

Channel 1 is for the BRAT's right knee. Adjust and set the min and max positions as shown in Figure 5-1 and 5-2. Note, you do not have to change

258

the angles because the knee can reach +/-90°.

259

Move the slider back to 0° before going on to the next servo.

</td>

</tr>

<tr>

</tr>

<tr>

Figure 5-1.

</td>

Figure 5-2.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Step 6.

279

Channel 2 is for the BRAT's right hip. Adjust the hip as in Figure 6-1 and set the minimum (-90°) position. Adjust the hip as in Figure 16-2

280

and set the maximum (45°) position. For clarity, the knees were bent in Figure 6-2.

281

Move the slider back to 0° before going on to the next servo.

</td>

</tr>

<tr>

</tr>

<tr>

Figure 6-1.

</td>

Figure 6-2.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 7.

302

The robot's right side is now configured. You can now configure the robot's left side. Click on the "Bank 3" button to gain access to

303

channels 16-23. Channel 16 is the right ankle, 17 is the right knee, and 18 is the right hip. Configuring these channels is identical to

304

configuring channels 0-2 with one exception: After you are done with the normal configuration, you must click on the "Reverse"

305

checkbox for these three channels! Make sure all servos are set to 0° (home) and save your work. For this robot, "home" position is

306

with all the servos set to their 0° position. However, any position you leave the sliders in when you save the configuration is how the robot

307

will look when you start Sequencer. In other words, "home" position does not have to be the 0° position, that's just what we used.</td>

Figure 7.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left" colspan="2">Save your work! The .cfg file will need to be loaded

317

each time you run the program. If you only have one robot to set up, save over the "ConfigSSC32.cfg" file. However, if you plan on

318

using the sequencer with more than one robot, then input a new file name, such as "BipedBRAT.cfg" It's important that you save these

319

files in the install directory, default C:\Program Files\Sequencer_SSC-32\</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 8.

326

Now we're going to import a pre-made project. This will enable you to use other people's projects on your robot.

327

Download <a href="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-seq/WebHome/minibipd.zip">this zip file</a>. It contains several projects. Unzip it into the

328

SEQ install directory. By default, it is C:\Program Files\Sequencer_SSC-32\

329

Click on "Project" in the upper left corner.</td>

Figure 8.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 9.

339

Click on "Import," then select "biped6-long stride.csv" and click "Open," then "OK."

340

Enter a project name or leave the default, then click "OK." You should see an "Import

success" message.

Click "Exit."

</td>

Figure 9.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 10.

354

Now for some fun! Let's make that robot walk!

355

Click on "Sequencer" as shown in Figure 10-1.

356

From the drop down menu in the project section, select "biped6-long stride."

357

In the Play menu, click on "Project Loop" as shown in Figure 10-3. Caution, the robot will start

358

moving immediately. To stop the robot, click on the black "stop" or "pause" buttons.

359

If everything went well, your robot should have walked across the table. If it appears that the legs are moving

360

in the same positions, you may have forgotten to reverse the servos on the robot's left side.

</td>

Figure 10-1.</td>

</tr>

<tr>

</tr>

<tr>

Figure 10-2.</td>

Figure 10-3.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 11.

382

Refer to Table 11 for a list of the projects included in the zip file and a video link when available.

383

After you're comfortable with playing projects, you can consult the Sequencer manual for more information on

384

how to create your own. Remember to send us images and videos of your cool projects so we can publish them online!

</td>

<td >

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Project File</td>

396

<td align="center" bordercolor="#808080" bgcolor="#C0C0C0">Video Link</td>

397

</tr>

398

<tr>

399

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Balance on Ankle</td>

400

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv04.mpg">Video</a>></td>

401

</tr>

402

<tr>

403

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Balance</td>

404

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv06.mpg">Video</a>></td>

</tr>

<tr>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv05.mpg">Video</a>></td>

413

</tr>

414

<tr>

415

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Get up from Front</td>

416

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv01.mpg">Video</a>></td>

417

</tr>

418

<tr>

419

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Headbutt</td>

420

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv07.mpg">Video</a>></td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv03.mpg">Video</a>></td>

425

</tr>

426

<tr>

427

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Long Stride</td>

428

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv08.mpg">Video</a>></td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv09.mpg">Video</a>></td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF"><<a href="http://www.lynxmotion.com/images/video/bp6srv02.mpg">Video</a>></td>

</tr>

</tbody></table>

</div>

</td>

</tr>

<tr>

<td >

Table 11

</td>

</tr>

</tbody></table>

</center>

</div>

</td>

</tr>

<tr>

</td>

</tr>

<tr>

III. Creating a Walking Sequence

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 1.

466

Run the Sequencer program.

467

Select the "empty" project from the Project drop down menu, and click on the black "+" to

468

make a new project. Enter a name for your project. As we are making the robot walk, a name such as "BRAT-Walk" might be applicable.</td>

Figure 1.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 2.

477

Now we're faced with an empty project and a screen full of servo blocks. To make the screen more manageable, click on "Swap" at the

478

top. This will swap the selected servos with the unselected ones. Since no servos are unselected, this will clear the screen.

479

Now just click on the servos that you need, which should be servos 0, 1, 2, 16, 17, and 18.</td>

Figure 2.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 3.

488

You can click and drag the servo boxes to arrange them so they resemble the robot's physical layout.</td>

Figure 3.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 4.

498

You can also name the servos by clicking on the number in the servo box. It will bring up the screen in Figure 4. In addition to naming the

499

servo, you can change the color of the servo box.</td>

Figure 4.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 5.

508

Now we're almost ready to make the robot walk. First, here's an outline of the walking sequence. The last two steps are just mirror images of

509

the first two steps.</td>

<td >

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Shift weight to robot's right</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Step forward</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Shift weight to robot's left</td>

</tr>

<tr>

<td align="center" bordercolor="#C0C0C0" bgcolor="#FFFFFF">Step forward</td>

</tr>

</tbody></table>

</div>

</td>

</tr>

<tr>

Table 5.</td>

</tr>

</tbody></table>

</center></div>

</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 6.

551

To make this project even easier, click on the "A<img border="0" src="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/servo-erector-set-robots-kits/ses-v1-robots/ses-v1-bipeds/brat-biped-seq/WebHome/link.gif" >B"

552

button in the lower left corner. This screen allows you to link servos together. Click on "Servo 1" on the left side and "Servo

553

17" on the right, then click "Add." Do the same with Servos 2 and 18. This will allow you to switch the positions of the right

554

and left legs with just a few clicks.</td>

Figure 6.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 7.

565

The first step in this walk is to get the robot into position to take a stride in the second step. Set your servos to the degrees shown in Table

566

7. They don't have to be exact; close will do. When you're done, click on the red "=" in the Step section to overwrite Step 1.

<td >

</tr>

<tr>

</tr>

<tr>

</tr>

</tbody></table>

</div></td>

</tr>

<tr>

Table 7.</td>

</tr>

</tbody></table>

</center></div>

</td>

Figure 7.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 8.

612

Now, click on "A<=>B" and deselect the "Selected step" check box and click OK. Then click the green "+" in

613

the Step section to add the current position as a new step.</td>

Figure 8.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 9.

622

To shift the robot's weight, just use the sliders and switch the degrees for Servos 0 and 16. Click on the green "+" in the Step

623

section when you're done to add this as a new step.</td>

Figure 9.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 10.

633

Now all you have to do is take another step! Click on the "A<=>B" button again, deselect "Selected step" if it

634

isn't already, and click OK. Click on the green "+" in the Step section when you're done.</td>

Figure 10.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 11.

643

To test the walk sequence, click on the sequence loop button on the right side of the screen under "Play." You can stop or pause the

644

walking sequence from the Play menu.

645

If you were successful, the robot should be walking now. If the robot doesn't walk in a straight line, try

646

increasing the ankle degrees so that more weight is shifted.

</td>

Figure 11.</td>

</tr>

<tr>

</tr>

<tr>

<td valign="top" align="left">Step 12.

657

To adjust the biped's walking speed, you can use the "Advanced Play" feature. Click on the Advanced Play button on the right side of

the screen.</td>

Figure 12.</td>

</tr>

<tr>

</td>

</tr>

<tr>

<td valign="top" align="left">Step 13.

669

By moving the Time slider, you will adjust the speed of all the servos in the project to a percentage of the normal speed. 100% is the project's

670

normal speed. Moving the slider below 100% causes the robot to move faster, while above 100% slows the robot down.

671

Click on the Loop button to test your new speed. You can tweak the speed while the robot is moving to get it

672

perfect.

673

If you click on the Apply button, the new speed will be applied to the project. </td>

Figure 13.</td>

</tr>

</tbody></table>

</body>

Wiki source code of BRAT Biped SEQ Tutorial v2.01XE

Navigation

Recently Visited