Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -162,8 +162,8 @@
162	162	| 15|[[**G**yre direction (**G**)>>||anchor="H15.GyreRotationDirection28G29"]]| G| QG| CG|✓| ✓| ✓|none |(% style="width:510px" %)Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)|(% style="text-align:center; width:113px" %)1
163	163	| 16|[[**ID** #>>||anchor="H16.IdentificationNumber28ID29"]]| | QID| CID| | | ✓|none (integer from 0 to 250)|(% style="width:510px" %)Note: ID 254 is a "broadcast" which all servos respond to. |(% style="text-align:center; width:113px" %)0
164	164	| 17|[[**B**aud rate>>||anchor="H17.BaudRate"]]| | QB| CB| | | ✓|none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)9600
165		-| 18|//{coming soon}//| | | | | | | |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
166		-
	165	+| 18|[[**F**irst Position (**P**ulse)>>||anchor="H18.FirstPosition28Pulse2928FP29"]]| | QFP|CFP |X| ✓| ✓|none |(% style="width:510px" %)CFP overwrites CFD and vice-versa|(% style="text-align:center; width:113px" %)(((
	166	+Limp
167	167	)))
168	168	| 19|[[**F**irst Position (**D**eg)>>||anchor="H19.FirstPosition28Degrees2928FD29"]]| | QFD|CFD|X| ✓| ✓|none |(% style="width:510px" %)CFD overwrites CFP and vice-versa|(% style="text-align:center; width:113px" %)Limp
169	169	| 20|[[**M**odel **S**tring>>||anchor="H20.QueryModelString28QMS29"]]| | QMS| | | | |none (string)|(% style="width:510px" %) Returns the type of servo (ST, HS, HT)|(% style="text-align:center; width:113px" %)
...	...	@@ -456,10 +456,22 @@
456	456
457	457	Sending this command will change the baud rate associated with servo ID 5 to 9600 bits per second.
458	458
459		-====== __18. {//Coming soon//}__ ======
	459	+====== __18. First Position (Pulse) (**FP**)__ ======
460	460
461		-Command coming soon....
	461	+In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only. If a first position pulse is assigned, the servo will move to that angle and hold there for up to 2 seconds before going limp should a new pulse not be received.
462	462
	463	+Query First Position in Pulses (**QFP**)
	464	+
	465	+Ex: #5QFP<cr> might return *5QFP1550<cr>
	466	+
	467	+The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds. If no first position has been set, servo will respond with DIS ("disabled").
	468	+
	469	+Configure First Position in Pulses (**CFP**)
	470	+
	471	+Ex: #5CP1550<cr>
	472	+
	473	+This configuration command means the servo, when set to RC mode, will immediately move to an angle equivalent to having received an RC pulse of 1550 microseconds upon power up. Sending a CFP command without a number (Ex. #5CFP<cr>) results in the servo remaining limp upon power up (i.e. disabled).
	474	+
463	463	====== __19. First Position (Degrees) (**FD**)__ ======
464	464
465	465	In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
...	...	@@ -671,10 +671,8 @@
671	671
672	672	====== __A5: Motion Control (**EM**)__ ======
673	673
674		-The command EM0 disables use of the motion controller (acceleration, velocity / travel, deceleration). As such, the servo will move at full speed for all motion commands. The command EM1 enables use of the motion controller.
	686	+{More details to come}
675	675
676		-Note that if the modifiers S or T are used, it is assumed that motion control is desired, and for that command, EM1 will be used.
677		-
678	678	====== __A6. Configure LED Blinking (**CLB**)__ ======
679	679
680	680	This command allows you to control when the RGB LED will blink the user set color (see [[16. RGB LED>>||anchor="H16.RGBLED28LED29"]] for details). This is very useful when visually seeing what the servo is doing. You can turn on or off blinking for various LSS status. The command requires that the servo be RESET. Here is the list and their associated value: