Summary

• Page properties (4 modified, 0 added, 0 removed)

Details

Page properties

Title

...	...	@@ -1,1 +1,1 @@
1		-LSS - Communication Protocol
	1	+lss-communication-protocol

Parent

...	...	@@ -1,1 +1,1 @@
1		-LynxmotionSmartServo.WebHome
	1	+lynxmotion-smart-servo.WebHome

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.BDaouas
	1	+xwiki:XWiki.RB1

Content

...	...	@@ -79,7 +79,7 @@
79	79
80	80	== Configuration Commands ==
81	81
82		-Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session.. Not all action commands have a corresponding configuration command and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:LynxmotionSmartServo.LSS - RC PWM.WebHome]]. Configuration commands are not cumulative, in that if two configurations are sent, one after the next, only the last configuration is used and stored. The format to send a configuration command is identical to that of an action command:
	82	+Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session.. Not all action commands have a corresponding configuration command and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:lynxmotion-smart-servo.LSS - RC PWM.WebHome]]. Configuration commands are not cumulative, in that if two configurations are sent, one after the next, only the last configuration is used and stored. The format to send a configuration command is identical to that of an action command:
83	83
84	84	1. Start with a number sign # (U+0023)
85	85	1. Servo ID number as an integer
...	...	@@ -557,7 +557,7 @@
557	557
558	558	This command would place the servo in RC wheel mode after a RESET or power cycle. Note that after a RESET or power cycle, the servo will be in RC mode and will not reply to serial commands. Using the command #5CRC<cr> or #5CRC3<cr> which requests that the servo remain in serial mode still requires a RESET command.
559	559
560		-Important note:** **To revert from RC mode back to serial mode, the [[LSS - Button Menu>>doc:LynxmotionSmartServo.LSS-ButtonMenu.WebHome]] is required. Should the button be inaccessible (or broken) when the servo is in RC mode and the user needs to change to serial mode, a 5V constant HIGH needs to be sent to the servo's Rx pin (RC PWM pin), ensuring a common GND and wait for 30 seconds. Normal RC PWM pulses should not exceed 2500 milliseconds. After 30 seconds, the servo will interpret this as a desired mode change and change to serial mode. This has been implemented as a fail safe.
	560	+Important note:** **To revert from RC mode back to serial mode, the [[LSS - Button Menu>>doc:lynxmotion-smart-servo.lss-button-menu.WebHome]] is required. Should the button be inaccessible (or broken) when the servo is in RC mode and the user needs to change to serial mode, a 5V constant HIGH needs to be sent to the servo's Rx pin (RC PWM pin), ensuring a common GND and wait for 30 seconds. Normal RC PWM pulses should not exceed 2500 milliseconds. After 30 seconds, the servo will interpret this as a desired mode change and change to serial mode. This has been implemented as a fail safe.
561	561
562	562	====== __28. **RESET**__ ======
563	563