Summary

• Page properties (2 modified, 0 added, 0 removed)
• Objects (0 modified, 3 added, 0 removed)
  • XWiki.XWikiRights[0]
  • XWiki.XWikiRights[1]
  • XWiki.XWikiRights[2]

Details

Page properties

Parent

...	...	@@ -1,1 +1,1 @@
1		-lynxmotion-smart-servo.WebHome
	1	+Lynxmotion Smart Servo (LSS).WebHome

Content

...	...	@@ -1,5 +1,5 @@
1	1	(% class="wikigeneratedid" id="HTableofContents" %)
2		-**Page Contents**
	2	+**Table of Contents**
3	3
4	4	{{toc depth="3"/}}
5	5
...	...	@@ -79,7 +79,7 @@
79	79
80	80	== Configuration Commands ==
81	81
82		-Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session.. Not all action commands have a corresponding configuration command and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:lynxmotion-smart-servo.lss-radio-control-pwm.WebHome]]. Configuration commands are not cumulative, in that if two configurations are sent, one after the next, only the last configuration is used and stored. The format to send a configuration command is identical to that of an action command:
	82	+Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not (see each command for details). Not all action commands have a corresponding configuration and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:Lynxmotion Smart Servo (LSS).LSS - RC PWM.WebHome]]. Configuration commands are not cumulative, in that if two configurations are sent, one after the next, only the last configuration is used and stored. The format to send a configuration command is identical to that of an action command:
83	83
84	84	1. Start with a number sign # (U+0023)
85	85	1. Servo ID number as an integer
...	...	@@ -128,71 +128,71 @@
128	128
129	129	= Command List =
130	130
131		-== Regular ==
132		-
133		-|= #|=Description|= Action|= Query|= Config|=Session|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
134		-| 1|[[**L**imp>>||anchor="H1.Limp28L29"]]| L| | | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
135		-| 2|[[**H**alt & **H**old>>||anchor="H2.Halt26Hold28H29"]]| H| | | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
136		-| 3|[[**T**imed move>>||anchor="H3.Timedmove28T29modifier"]]| T| | | | | ✓|milliseconds|(% style="width:510px" %) Modifier only for {P, D, MD}|(% style="text-align:center; width:113px" %)
137		-| 4|[[**S**peed>>||anchor="H4.Speed28S29modifier"]]| S|QS| | | | ✓|microseconds per second|(% style="width:510px" %) Modifier only {P}|(% style="text-align:center; width:113px" %)
138		-| 5|[[**M**ove in **D**egrees (relative)>>||anchor="H5.28Relative29MoveinDegrees28MD29"]]| MD| | | | | ✓|tenths of degrees (ex 325 = 32.5 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
139		-| 6|[[**O**rigin Offset>>||anchor="H6.OriginOffsetAction28O29"]]| O| QO|CO|✓| ✓| ✓|tenths of degrees (ex 91 = 9.1 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
	131	+|= #|=Description|= Action|= Query|= Config|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
	132	+| 1|[[**L**imp>>||anchor="H1.Limp28L29"]]| L| | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	133	+| 2|[[**H**alt & **H**old>>||anchor="H2.Halt26Hold28H29"]]| H| | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	134	+| 3|[[**T**imed move>>||anchor="H3.Timedmove28T29"]]| T| | | | ✓|milliseconds|(% style="width:510px" %) Modifier only for {P, D, MD}|(% style="text-align:center; width:113px" %)
	135	+| 4|[[**S**peed>>||anchor="H4.Speed28S29"]]| S| | | | ✓|microseconds per second|(% style="width:510px" %) Modifier only {P}|(% style="text-align:center; width:113px" %)
	136	+| 5|[[**M**ove in **D**egrees (relative)>>||anchor="H5.28Relative29MoveinDegrees28MD29"]]| MD| | | | ✓|tenths of degrees (ex 325 = 32.5 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	137	+| 6|[[**O**rigin Offset>>||anchor="H6.OriginOffsetAction28O29"]]| O| QO| __CO__| ✓| ✓|tenths of degrees (ex 91 = 9.1 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
140	140	0
141	141	)))
142		-| 7|[[**A**ngular **R**ange>>||anchor="H7.AngularRange28AR29"]]| AR| QAR| CAR|✓| ✓| ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
	140	+| 7|[[**A**ngular **R**ange>>||anchor="H7.AngularRange28AR29"]]| AR| QAR| CAR| ✓| ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
143	143	1800
144	144	)))
145		-| 8|[[Position in **P**ulse>>||anchor="H8.PositioninPulse28P29"]]| P| QP| | | | ✓|microseconds|(% style="width:510px" %)(((
	143	+| 8|[[Position in **P**ulse>>||anchor="H8.PositioninPulse28P29"]]| P| QP| | | ✓|microseconds|(% style="width:510px" %)(((
146	146	Inherited from SSC-32 serial protocol
147	147	)))|(% style="text-align:center; width:113px" %)
148		-| 9|[[Position in **D**egrees>>||anchor="H9.PositioninDegrees28D29"]]| D| QD / QDT| | | | ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
149		-| 10|[[**W**heel mode in **D**egrees>>||anchor="H10.WheelModeinDegrees28WD29"]]| WD| QWD| | | | ✓|tenths of degrees per second (ex 248 = 24.8 degrees per second)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
150		-| 11|[[**W**heel mode in **R**PM>>||anchor="H11.WheelModeinRPM28WR29"]]| WR| QWR| | | | ✓|revolutions per minute (rpm)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
151		-| 12|[[Max **S**peed in **D**egrees>>||anchor="H12.MaxSpeedinDegrees28SD29"]]| SD| QSD|CSD|✓| ✓| ✓|degrees per second (°/s)|(% style="width:510px" %)(((
	146	+| 9|[[Position in **D**egrees>>||anchor="H9.PositioninDegrees28D29"]]| D| QD| | | ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	147	+| 10|[[**W**heel mode in **D**egrees>>||anchor="H10.WheelModeinDegrees28WD29"]]| WD| QWD| | | ✓|tenths of degrees per second (ex 248 = 24.8 degrees per second)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
	148	+| 11|[[**W**heel mode in **R**PM>>||anchor="H11.WheelModeinRPM28WR29"]]| WR| QWR| | | ✓|revolutions per minute (rpm)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
	149	+| 12|[[Max **S**peed in **D**egrees>>||anchor="H12.SpeedinDegrees28SD29"]]| SD| QSD|CSD| ✓| ✓|tenths of degrees per second |(% style="width:510px" %)(((
152	152	QSD: Add modifier "2" for instantaneous speed.
153	153
154	154	SD overwrites SR / CSD overwrites CSR and vice-versa.
155	155	)))|(% style="text-align:center; width:113px" %)Max per servo
156		-| 13|[[Max **S**peed in **R**PM>>||anchor="H13.MaxSpeedinRPM28SR29"]]| SR| QSR|CSR|✓| ✓| ✓|revolutions per minute (rpm)|(% style="width:510px" %)(((
	154	+| 13|[[Max **S**peed in **R**PM>>||anchor="H13.SpeedinRPM28SR29"]]| SR| QSR|CSR| ✓| ✓|revolutions per minute (rpm)|(% style="width:510px" %)(((
157	157	QSR: Add modifier "2" for instantaneous speed
158	158
159	159	SR overwrites SD / CSR overwrites CSD and vice-versa.
160	160	)))|(% style="text-align:center; width:113px" %)Max per servo
161		-| 14|[[**LED** Color>>||anchor="H14.LEDColor28LED29"]]| LED| QLED| CLED|✓| ✓| ✓|none (integer from 0 to 8)|(% style="width:510px" %)0=Off (black); 1=Red 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White;|(% style="text-align:center; width:113px" %)7
162		-| 15|[[**G**yre direction (**G**)>>||anchor="H15.GyreRotationDirection28G29"]]| G| QG| CG|✓| ✓| ✓|none |(% style="width:510px" %)Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)|(% style="text-align:center; width:113px" %)1
163		-| 16|[[**ID** #>>||anchor="H16.IdentificationNumber28ID29"]]| | QID| CID| | | ✓|none (integer from 0 to 250)|(% style="width:510px" %)Note: ID 254 is a "broadcast" which all servos respond to. |(% style="text-align:center; width:113px" %)0
164		-| 17|[[**B**aud rate>>||anchor="H17.BaudRate"]]| | QB| CB| | | ✓|none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)9600
165		-| 18|//{coming soon}//| | | | | | | |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
166		-
	159	+| 16|[[**LED** Color>>||anchor="H16.RGBLED28LED29"]]| LED| QLED| CLED| ✓| ✓|none (integer from 0 to 8)|(% style="width:510px" %)0=Off (black); 1=Red 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White;|(% style="text-align:center; width:113px" %)7
	160	+| 17|[[**ID** #>>||anchor="H17.IdentificationNumber"]]| | QID| CID| | ✓|none (integer from 0 to 250)|(% style="width:510px" %)Note: ID 254 is a "broadcast" which all servos respond to|(% style="text-align:center; width:113px" %)0
	161	+| 18|[[**B**aud rate>>||anchor="H18.BaudRate"]]| B| QB| CB| | ✓|none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)9600
	162	+| 19|[[**G**yre direction (**G**)>>||anchor="H19.GyreRotationDirection"]]| G| QG| CG| ✓| ✓|none |(% style="width:510px" %)Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)|(% style="text-align:center; width:113px" %)1
	163	+| 20|[[**F**irst Position (**P**ulse)>>||anchor="H20.First2InitialPosition28pulse29"]]| | QFP|CFP | ✓| ✓|none |(% style="width:510px" %)CFP overwrites CFD and vice-versa|(% style="text-align:center; width:113px" %)(((
	164	+Limp
167	167	)))
168		-| 19|[[**F**irst Position (**D**eg)>>||anchor="H19.FirstPosition28Degrees2928FD29"]]| | QFD|CFD|X| ✓| ✓|none |(% style="width:510px" %)CFD overwrites CFP and vice-versa|(% style="text-align:center; width:113px" %)Limp
169		-| 20|[[**M**odel **S**tring>>||anchor="H20.QueryModelString28QMS29"]]| | QMS| | | | |none (string)|(% style="width:510px" %) Returns the type of servo (ST, HS, HT)|(% style="text-align:center; width:113px" %)
170		-| 21|[[Serial **N**umber>>||anchor="H21.QuerySerialNumber28QN29"]]| | QN| | | | |none (integer)|(% style="width:510px" %) Returns the unique serial number for that servo|(% style="text-align:center; width:113px" %)
171		-| 22|[[**F**irmware version>>||anchor="H22.QueryFirmware28QF29"]]| | QF| | | | |none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
172		-| 23|[[**Q**uery (gen. status)>>||anchor="H23.QueryStatus28Q29"]]| | Q| | | | ✓|none (integer from 1 to 8)|(% style="width:510px" %) See command description for details|(% style="text-align:center; width:113px" %)
173		-| 24|[[**V**oltage>>||anchor="H24.QueryVoltage28QV29"]]| | QV| | | | ✓|millivolts (ex 5936 = 5936mV = 5.936V)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
174		-| 25|[[**T**emperature>>||anchor="H25.QueryTemperature28QT29"]]| | QT| | | | ✓|tenths of degrees Celsius|(% style="width:510px" %)Max temp before error: 85°C (servo goes limp)|(% style="text-align:center; width:113px" %)
175		-| 26|[[**C**urrent>>||anchor="H26.QueryCurrent28QC29"]]| | QC| | | | ✓|milliamps (ex 200 = 0.2A)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
176		-| 27|[[**C**hange to** RC**>>||anchor="H27.ConfigureRCMode28CRC29"]]| | |CRC|✓| | ✓|none|(% style="width:510px" %)(((
177		-Change to RC mode 1 (position) or 2 (wheel).
	166	+| 21|[[**F**irst Position (**D**egrees)>>||anchor="H21.First2InitialPosition28Degrees29"]]| | QFD|CFD| ✓| ✓|none |(% style="width:510px" %)CFD overwrites CFP and vice-versa|(% style="text-align:center; width:113px" %)Limp
	167	+| 22|[[**T**arget (**D**egree) **P**osition>>||anchor="H22.QueryTargetPositioninDegrees28QDT29"]]| | QDT| | | ✓|tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	168	+| 23|[[**M**odel **S**tring>>||anchor="H23.QueryModelString28QMS29"]]| | QMS| | | |none (string)|(% style="width:510px" %) Returns the type of servo (ST, HS, HT)|(% style="text-align:center; width:113px" %)
	169	+| 24|[[Serial **N**umber>>||anchor="H24.QuerySerialNumber28QN29"]]| | QN| | | |none (integer)|(% style="width:510px" %) Returns the unique serial number for that servo|(% style="text-align:center; width:113px" %)
	170	+| 25|[[**F**irmware version>>||anchor="H25.QueryFirmware28QF29"]]| | QF| | | |none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	171	+| 26|[[**Q**uery (general status)>>||anchor="H26.QueryStatus28Q29"]]| | Q| | | ✓|none (integer from 1 to 8)|(% style="width:510px" %) See command description for details|(% style="text-align:center; width:113px" %)
	172	+| 27|[[**V**oltage>>||anchor="H27.QueryVoltage28QV29"]]| | QV| | | ✓|millivolts (ex 5936 = 5936mV = 5.936V)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	173	+| 28|[[**T**emperature>>||anchor="H28.QueryTemperature28QT29"]]| | QT| | | ✓|tenths of degrees Celsius|(% style="width:510px" %)Max temp before error: 85°C (servo goes limp)|(% style="text-align:center; width:113px" %)
	174	+| 29|[[**C**urrent>>||anchor="H29.QueryCurrent28QC29"]]| | QC| | | ✓|milliamps (ex 200 = 0.2A)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	175	+| 30a|[[**RC** Mode>>||anchor="H30.RCMode28CRC29"]] - Position| | |CRC1| | ✓|none|(% style="width:510px" %)(((
	176	+Puts the servo into RC mode. To revert to smart mode, use the button menu.
178	178	)))|(% style="text-align:center; width:113px" %)Serial
179		-| 28|[[**RESET**>>||anchor="H28.RESET"]]| | | | | | ✓|none|(% style="width:510px" %)Soft reset. See command for details.|(% style="text-align:center; width:113px" %)
180		-| 29|[[**DEFAULT**>>||anchor="H29.DEFAULTA026CONFIRM"]]| | | | | |✓|none|(% style="width:510px" %)Revert to firmware default values. See command for details|(% style="text-align:center; width:113px" %)
181		-| 30|[[**UPDATE**>>||anchor="H30.UPDATEA026CONFIRM"]]| | | | | |✓|none|(% style="width:510px" %)Update firmware. See command for details.|(% style="text-align:center; width:113px" %)
	178	+| 30b|[[**RC** Mode>>||anchor="H30.RCMode28CRC29"]] - Wheel| | |CRC2| | ✓| |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
	179	+| 31|[[**RESET**>>||anchor="H31.RESET"]]| | | | | ✓|none|(% style="width:510px" %)Soft reset. See command for details.|(% style="text-align:center; width:113px" %)
	180	+| 32|[[**DEFAULT**>>||anchor="H32.DEFAULTA026CONFIRM"]]| | | | |✓|none|(% style="width:510px" %)Revert to firmware default values. See command for details|(% style="text-align:center; width:113px" %)
	181	+| 33|[[**UPDATE**>>||anchor="H33.UPDATEA026CONFIRM"]]| | | | |✓|none|(% style="width:510px" %)Update firmware. See command for details.|(% style="text-align:center; width:113px" %)
182	182
183	183	== Advanced ==
184	184
185		-|= #|=Description|= Action|= Query|= Config|=Session|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes
186		-| A1|[[**A**ngular **S**tiffness>>||anchor="HA1.AngularStiffness28AS29"]]|AS|QAS|CAS|✓| ✓| ✓|none (integer -4 to +4)|(% style="width:510px" %)Suggested values are between 0 to +4
187		-| A2|[[**A**ngular **H**olding Stiffness>>||anchor="HA2.AngularHoldingStiffness28AH29"]]|AH|QAH|CAH|✓| | ✓|none (integer -10 to +10)|(% style="width:510px" %)Effect is different between serial and RC
188		-| A3|[[**A**ngular **A**cceleration>>||anchor="HA3:AngularAcceleration28AA29"]]|AA|QAA|CAA|✓| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared
189		-| A4|[[**A**ngular **D**eceleration>>||anchor="HA4:AngularDeceleration28AD29"]]|AD|QAD|CAD|✓| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared
190		-| A5|[[**E**nable **M**otion Control>>||anchor="HA5:MotionControl28EM29"]]|EM|QEM| | | | ✓|none|(% style="width:510px" %)EM0 to disable motion control, EM1 to enable
191		-| A6|[[**C**onfigure **L**ED **B**linking>>||anchor="HA6.ConfigureLEDBlinking28CLB29"]]| |QLB| CLB| | ✓| ✓|none (integer from 0 to 63)|(% style="width:510px" %)(((
	185	+|= #|=Description|= Action|= Query|= Config|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
	186	+| A1|[[**A**ngular **S**tiffness>>||anchor="H14.AngularStiffness28AS29"]]| AS|QAS|CAS| ✓| ✓|none (integer -4 to +4)|(% style="width:510px" %)Suggested values are between 0 to +4|(% style="text-align:center; width:113px" %)0
	187	+| A2|[[**A**ngular **H**olding Stiffness>>||anchor="H15.AngularHoldStiffness28AH29"]]|AH|QAH|CAH| | ✓|none (integer -10 to +10)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)1
	188	+| A3|[[**A**ngular **A**cceleration>>||anchor="H15b:AngularAcceleration28AA29"]]|AA|QAA|CAA| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared|(% style="text-align:center; width:113px" %)
	189	+| A4|[[**A**ngular **D**eceleration>>||anchor="H15c:AngularDeceleration28AD29"]]|AD|QAD|CAD| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared|(% style="text-align:center; width:113px" %)
	190	+| A5|[[**E**nable **M**otion Control>>||anchor="H15d:MotionControl28MC29"]]|EM|QEM| | | ✓|none|(% style="width:510px" %)EM0 to disable motion control, EM1 to enable|(% style="text-align:center; width:113px" %)
	191	+| A6|[[**C**onfigure **L**ED **B**linking>>||anchor="H16b.ConfigureLEDBlinking28CLB29"]]| | | CLB| ✓| |none (integer from 0 to 63)|(% style="width:510px" %)(((
192	192	0=No blinking, 63=Always blink;
193	193
194		-Blink while: 1=Limp; 2=Holding; 4=Accel; 8=Decel; 16=Free 32=Travel;
195		-)))
	194	+Blink while: 1=Limp; 2=Holding 4=Accel; 8=Decel; 16=Free 32=Travel;
	195	+)))|(% style="text-align:center; width:113px" %)
196	196
197	197	== Details ==
198	198
...	...	@@ -208,7 +208,7 @@
208	208
209	209	This action overrides whatever the servo might be doing at the time the command is received (accelerating, moving continuously etc.) and causes it to stop immediately and hold that angular position.
210	210
211		-====== __3. Timed move (**T**) modifier__ ======
	211	+====== __3. Timed move (**T**)__ ======
212	212
213	213	Example: #5P1500T2500<cr>
214	214
...	...	@@ -216,18 +216,12 @@
216	216
217	217	Note: If the calculated speed at which a servo must rotate for a timed move is greater than its maximum speed (which depends on voltage and load), then it will move at its maximum speed, and the time of the move may be longer than requested.
218	218
219		-====== __4. Speed (**S**) modifier__ ======
	219	+====== __4. Speed (**S**)__ ======
220	220
221	221	Example: #5P1500S750<cr>
222	222
223	223	This command is a modifier only for a position (P) action and determines the speed of the move in microseconds per second. A speed of 750 microseconds would cause the servo to rotate from its current position to the desired position at a speed of 750 microseconds per second. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.
224	224
225		-Query Speed (**QS**)
226		-
227		-Example: #5QS<cr> might return *5QS300<cr>
228		-
229		-This command queries the current speed in microseconds per second.
230		-
231	231	====== __5. (Relative) Move in Degrees (**MD**)__ ======
232	232
233	233	Example: #5MD123<cr>
...	...	@@ -286,7 +286,7 @@
286	286
287	287	Example: #5P2334<cr>
288	288
289		-The position in PWM pulses was retained in order to be backward compatible with the SSC-32 / 32U protocol. This relates the desired angle with an RC standard PWM pulse and is further explained in the SSC-32 and SSC-32U manuals found on Lynxmotion.com. Without any modifications to configuration considered, and a ±90.0 degrees standard range where 1500 microseconds is centered, a pulse of 2334 would set the servo to 165.1 degrees. Valid values for P are [500, 2500]. Values outside this range are corrected / restricted to end points.
	283	+The position in PWM pulses was retained in order to be backward compatible with the SSC-32 / 32U protocol. This relates the desired angle with an RC standard PWM pulse and is further explained in the SSC-32 and SSC-32U manuals found on Lynxmotion.com. Without any modifications to configuration considered, and a ±90.0 degrees standard range where 1500 microseconds is centered, a pulse of 2334 would set the servo to 165.1 degrees. Valid values for P are [500, 2500]. Values outside this range are corrected to end points.
290	290
291	291	Query Position in Pulse (**QP**)
292	292
...	...	@@ -309,13 +309,6 @@
309	309
310	310	This means the servo is located at 13.2 degrees.
311	311
312		-(% class="wikigeneratedid" id="H22.QueryTargetPositioninDegrees28QDT29" %)
313		-Query Target Position in Degrees (**QDT**)
314		-
315		-Ex: #5QDT<cr> might return *5QDT6783<cr>
316		-
317		-The query target position command returns the target angle during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond without a number (Ex: *5QDT<cr>).
318		-
319	319	====== __10. Wheel Mode in Degrees (**WD**)__ ======
320	320
321	321	Ex: #5WD900<cr>
...	...	@@ -340,22 +340,22 @@
340	340
341	341	The servo replies with the angular speed in rpm. A negative sign would indicate the opposite direction (for factory default a negative value would be counter clockwise).
342	342
343		-====== __12. Max Speed in Degrees (**SD**)__ ======
	330	+====== __12. Speed in Degrees (**SD**)__ ======
344	344
345	345	Ex: #5SD1800<cr>
346	346
347		-This command sets the servo's maximum speed for motion commands in tenths of degrees per second for that session. In the example above, the servo's maximum speed for that session would be set to 180.0 degrees per second. The servo's maximum speed cannot be set higher than its physical limit at a given voltage. The SD action command overrides CSD (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSD as described below. Note that SD and SR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) received is what the servo uses for that session.
	334	+This command sets the servo's maximum speed for action commands in tenths of degrees per second for that session. In the example above, the servo's maximum speed for that session would be set to 180.0 degrees per second. Therefore maximum speed for actions can be set "on the fly". The servo's maximum speed cannot be set higher than its physical limit at a given voltage. SD overrides CSD (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSD as described below. Note that SD and SR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) is what the servo uses for that session.
348	348
349	349	Query Speed in Degrees (**QSD**)
350	350
351	351	Ex: #5QSD<cr> might return *5QSD1800<cr>
352	352
353		-By default QSD will return the current session value, which is set to the value of CSD as reset/power cycle and changed whenever an SD/SR command is processed.
	340	+By default QSD will return the current session value, which is set to the value of CSD as reset/power cycle and changed whenever a SD/SR command is processed.
354	354	If #5QSD1<cr> is sent, the configured maximum speed (CSD value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:
355	355
356	356	|**Command sent**|**Returned value (1/10 °)**
357	357	|ex: #5QSD<cr>|Session value for maximum speed (set by latest SD/SR command)
358		-|ex: #5QSD1<cr>|Configured maximum speed in EEPROM (set by CSD/CSR)
	345	+|ex: #5QSD1<cr>|Configured maximum speed  (set by CSD/CSR)
359	359	|ex: #5QSD2<cr>|Instantaneous speed (same as QWD)
360	360	|ex: #5QSD3<cr>|Target travel speed
361	361
...	...	@@ -365,22 +365,22 @@
365	365
366	366	Using the CSD command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 180.0 degrees per second. When the servo is powered on (or after a reset), the CSD value is used. Note that CSD and CSR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
367	367
368		-====== __13. Max Speed in RPM (**SR**)__ ======
	355	+====== __13. Speed in RPM (**SR**)__ ======
369	369
370	370	Ex: #5SD45<cr>
371	371
372		-This command sets the servo's maximum speed for motion commands in rpm for that session. In the example above, the servo's maximum speed for that session would be set to 45rpm. The servo's maximum speed cannot be set higher than its physical limit at a given voltage. SD overrides CSD (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSD as described below. Note that SD (described above) and SR are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) received is what the servo uses for that session.
	359	+This command sets the servo's maximum speed for action commands in rpm for that session. In the example above, the servo's maximum speed for that session would be set to 45rpm. Therefore maximum speed for actions can be set "on the fly". The servo's maximum speed cannot be set higher than its physical limit at a given voltage. SD overrides CSD (described below) for that session. Upon reset or power cycle, the servo reverts to the value associated with CSD as described below. Note that SD (described above) and SR are effectively the same, but allow the user to specify the speed in either unit. The last command (either SR or SD) is what the servo uses for that session.
373	373
374	374	Query Speed in Degrees (**QSR**)
375	375
376	376	Ex: #5QSR<cr> might return *5QSR45<cr>
377	377
378		-By default QSR will return the current session value, which is set to the value of CSR as reset/power cycle and changed whenever an SD/SR command is processed.
	365	+By default QSR will return the current session value, which is set to the value of CSR as reset/power cycle and changed whenever a SD/SR command is processed.
379	379	If #5QSR1<cr> is sent, the configured maximum speed (CSR value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:
380	380
381	381	|**Command sent**|**Returned value (1/10 °)**
382	382	|ex: #5QSR<cr>|Session value for maximum speed (set by latest SD/SR command)
383		-|ex: #5QSR1<cr>|Configured maximum speed in EEPROM (set by CSD/CSR)
	370	+|ex: #5QSR1<cr>|Configured maximum speed  (set by CSD/CSR)
384	384	|ex: #5QSR2<cr>|Instantaneous speed (same as QWR)
385	385	|ex: #5QSR3<cr>|Target travel speed
386	386
...	...	@@ -388,321 +388,288 @@
388	388
389	389	Ex: #5CSR45<cr>
390	390
391		-Using the CSR command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSR value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) received is what the servo uses for that session.
	378	+Using the CSR command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSR value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
392	392
393		-====== __14. LED Color (**LED**)__ ======
	380	+====== __14. Angular Stiffness (**AS**)__ ======
394	394
395		-Ex: #5LED3<cr>
	382	+The servo's rigidity / angular stiffness can be thought of as (though not identical to) a damped spring in which the value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes.
396	396
397		-This action sets the servo's RGB LED color for that session.The LED can be used for aesthetics, or (based on user code) to provide visual status updates. Using timing can create patterns.
	384	+A positive value of "angular stiffness":
398	398
399		-0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6= 7=MAGENTA, 8=WHITE
	386	+* The more torque will be applied to try to keep the desired position against external input / changes
	387	+* The faster the motor will reach its intended travel speed and the motor will decelerate faster and nearer to its target position
400	400
401		-Query LED Color (**QLED**)
	389	+A negative value on the other hand:
402	402
403		-Ex: #5QLED<cr> might return *5QLED5<cr>
	391	+* Causes a slower acceleration to the travel speed, and a slower deceleration
	392	+* Allows the target position to deviate more from its position before additional torque is applied to bring it back
404	404
405		-This simple query returns the indicated servo's LED color.
	394	+The default value is zero and the effect becomes extreme by -4, +4. There are no units, only integers between -4 to 4. Greater values produce increasingly erratic behavior.
406	406
407		-Configure LED Color (**CLED**)
	396	+Ex: #5AS-2<cr>
408	408
409		-Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle. Note that it also changes the session's LED color immediately as well.
	398	+This reduces the angular stiffness to -2 for that session, allowing the servo to deviate more around the desired position. This can be beneficial in many situations such as impacts (legged robots) where more of a "spring" effect is desired. Upon reset, the servo will use the value stored in memory, based on the last configuration command.
410	410
411		-====== __15. Gyre Rotation Direction (**G**)__ ======
	400	+Ex: #5QAS<cr>
412	412
413		-"Gyre" is defined as a circular course or motion. The effect of changing the gyre direction is as if you were to use a mirror image of a circle. CW = 1; CCW = -1. The factory default is clockwise (CW).
	402	+Queries the value being used.
414	414
415		-Ex: #5G-1<cr>
	404	+Ex: #5CAS<cr>
416	416
417		-This command will cause servo #5's positions to be inverted, effectively causing the servo to rotate in the opposite direction given the same command. For example in a 2WD robot, servos are often physically installed back to back, therefore setting one of the servos to a negative gyration, the same wheel command (ex WR30) to both servos will cause the robot to move forward or backward rather than rotate.
	406	+Writes the desired angular stiffness value to memory.
418	418
419		-Query Gyre Direction (**QG**)
	408	+====== __15. Angular Hold Stiffness (**AH**)__ ======
420	420
421		-Ex: #5QG<cr> might return *5QG-1<cr>
	410	+The angular holding stiffness determines the servo's ability to hold a desired position under load. Values can be from -10 to 10, with the default being 0. Note that negative values mean the final position can be easily deflected.
422	422
423		-The value returned above means the servo is in a counter-clockwise gyration.
	412	+Ex: #5AH3<cr>
424	424
425		-Configure Gyre (**CG**)
	414	+This sets the holding stiffness for servo #5 to 3 for that session.
426	426
427		-Ex: #5CG-1<cr>
	416	+Query Angular Hold Stiffness (**QAH**)
428	428
429		-This changes the gyre direction as described above and also writes to EEPROM.
	418	+Ex: #5QAH<cr> might return *5QAH3<cr>
430	430
431		-====== __16. Identification Number (**ID**)__ ======
	420	+This returns the servo's angular holding stiffness value.
432	432
433		-A servo's identification number cannot be set "on the fly" and must be configured via the CID command described below. The factory default ID number for all servos is 0. Since smart servos are intended to be daisy chained, in order to respond differently from one another, the user must set different identification numbers. Servos with the same ID and baud rate will all receive and react to the same commands (assuming same baud rate).
	422	+Configure Angular Hold Stiffness (**CAH**)
434	434
435		-Query Identification (**QID**)
	424	+Ex: #5CAH2<cr>
436	436
437		-EX: #254QID<cr> might return *QID5<cr>
	426	+This writes the angular holding stiffness of servo #5 to 2 to EEPROM
438	438
439		-When using the query ID command, it is best to only have one servo connected and thus receive only one reply. This is useful when you are not sure of the servo's ID, but don't want to change it. Using the broadcast command (ID 254) with only one servo will have that servo reply with its ID number (assuming the query is sent . Alternatively, pushing the button upon startup and temporarily setting the servo ID to 255 will still result in the servo responding with its "real" ID.
	428	+====== __15b: Angular Acceleration (**AA**)__ ======
440	440
441		-Configure ID (**CID**)
	430	+{More details to come}
442	442
443		-Ex: #4CID5<cr>
	432	+====== __15c: Angular Deceleration (**AD**)__ ======
444	444
445		-Setting a servo's ID in EEPROM is done via the CID command. All servos connected to the same serial bus will be assigned that ID. In most situations each servo must be set a unique ID, which means each servo must be connected individually to the serial bus and receive a unique CID number. It is best to do this before the servos are added to an assembly. Numbered stickers are provided to distinguish each servo after their ID is set, though you are free to use whatever alternative method you like. The servo must be RESET or power cycled in order for the new ID to take effect.
	434	+{More details to come}
446	446
447		-====== __17. Baud Rate__ ======
	436	+====== __15d: Motion Control (**EM**)__ ======
448	448
449		-A servo's baud rate cannot be set "on the fly" and must be configured via the CB command described below. The factory default baud rate for all servos is 9600. Since smart servos are intended to be daisy chained, in order to respond to the same serial bus, all servos in a project should ideally be set to the same baud rate. Setting different baud rates will have the servos respond differently and may create issues. Available baud rates are: 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115.2 kbps, 230.4 kbps, 250.0 kbps, 460.8 kbps, 500.0 kbps. Servos are shipped with a baud rate set to 9600. The baud rates are currently restricted to those above.
	438	+{More details to come}
450	450
451		-Query Baud Rate (**QB**)
	440	+====== __16. RGB LED (**LED**)__ ======
452	452
453		-Ex: #5QB<cr> might return *5QB9600<cr>
	442	+Ex: #5LED3<cr>
454	454
455		-Since the command to query the baud rate must be done at the servo's existing baud rate, it can simply be used to confirm the CB configuration command was correctly received before the servo is power cycled and the new baud rate takes effect.
	444	+This action sets the servo's RGB LED color for that session.The LED can be used for aesthetics, or (based on user code) to provide visual status updates. Using timing can create patterns.
456	456
457		-Configure Baud Rate (**CB**)
	446	+0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6= 7=MAGENTA, 8=WHITE
458	458
459		-Important Note: the servo's current session retains the given baud rate and the new baud rate will only take effect when the servo is power cycled / RESET.
	448	+Query LED Color (**QLED**)
460	460
461		-Ex: #5CB9600<cr>
	450	+Ex: #5QLED<cr> might return *5QLED5<cr>
462	462
463		-Sending this command will change the baud rate associated with servo ID 5 to 9600 bits per second.
	452	+This simple query returns the indicated servo's LED color.
464	464
465		-====== __18. {//Coming soon//}__ ======
	454	+Configure LED Color (**CLED**)
466	466
467		-Command coming soon....
	456	+Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle. Note that it also changes the session's LED color immediately as well.
468	468
469		-====== __19. First Position (Degrees) (**FD**)__ ======
	458	+====== __16b. Configure LED Blinking (**CLB**)__ ======
470	470
471		-In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
	460	+This command allows you to control when the RGB LED will blink the user set color (see [[16. RGB LED>>||anchor="H16.RGBLED28LED29"]] for details).
	461	+You can turn on or off blinking for various LSS status. Here is the list and their associated value: 0=No blinking, ; 63=Always blink; Blink while: 1=Limp; 2=Holding 4=Accel; 8=Decel; 16=Free 32=Travel;
472	472
473		-Query First Position in Degrees (**QFD**)
	463	+To set blinking, use CLB with the value of your choosing. To activate blinking in multiple status, simply add together the values of the corresponding status. See examples below:
474	474
475		-Ex: #5QFD<cr> might return *5QFD64<cr>
	465	+Ex: #5CLB0<cr> to turn off all blinking (LED always solid)
	466	+Ex: #5CLB1<cr> only blink when limp
	467	+Ex: #5CLB2<cr> only blink when holding
	468	+Ex: #5CLB12<cr> only blink when accel or decel
	469	+Ex: #5CLB48<cr> only blink when free or travel
	470	+Ex: #5CLB63<cr> blink in all status
476	476
477		-The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds.
	472	+====== __17. Identification Number__ ======
478	478
479		-Configure First Position in Degrees (**CFD**)
	474	+A servo's identification number cannot be set "on the fly" and must be configured via the CID command described below. The factory default ID number for all servos is 0. Since smart servos are intended to be daisy chained, in order to respond differently from one another, the user must set different identification numbers. Servos with the same ID and baud rate will all receive and react to the same commands.
480	480
481		-Ex: #5CD64<cr>
	476	+Query Identification (**QID**)
482	482
483		-This configuration command means the servo, when set to smart mode, will immediately move to 6.4 degrees upon power up. Sending a CFD command without a number (Ex. #5CFD<cr>) results in the servo remaining limp upon power up.
	478	+EX: #254QID<cr> might return *QID5<cr>
484	484
485		-====== __20. Query Model String (**QMS**)__ ======
	480	+When using the query ID command, it is best to only have one servo connected and thus receive only one reply using the broadcast command (ID 254). Alternatively, pushing the button upon startup and temporarily setting the servo ID to 255 will still result in the servo responding with its "real" ID.
486	486
487		-Ex: #5QMS<cr> might return *5QMSLSS-HS1cr>
	482	+Configure ID (**CID**)
488	488
489		-This reply means the servo model is LSS-HS1, meaning a high speed servo, first revision.
	484	+Ex: #4CID5<cr>
490	490
491		-====== __21. Query Serial Number (**QN**)__ ======
	486	+Setting a servo's ID in EEPROM is done via the CID command. All servos connected to the same serial bus will be assigned that ID. In most situations each servo must be set a unique ID, which means each servo must be connected individually to the serial bus and receive a unique CID number. It is best to do this before the servos are added to an assembly. Numbered stickers are provided to distinguish each servo after their ID is set, though you are free to use whatever alternative method you like.
492	492
493		-Ex: #5QN<cr> might return *5QN12345678<cr>
	488	+====== __18. Baud Rate__ ======
494	494
495		-The number in the response (12345678) would be the servo's serial number which is set and should not be changed by the user.
	490	+A servo's baud rate cannot be set "on the fly" and must be configured via the CB command described below. The factory default baud rate for all servos is 9600. Since smart servos are intended to be daisy chained, in order to respond to the same serial bus, all servos in that project should ideally be set to the same baud rate. Setting different baud rates will have the servos respond differently and may create issues. Available baud rates are: 9.6 kbps, 19.2 kbps, 38.4 kbps, 57.6 kbps, 115.2 kbps, 230.4 kbps, 250.0 kbps, 460.8 kbps, 500.0 kbps, 750.0 kbps*, 921.6 kbps*. Servos are shipped with a baud rate set to 9600. The baud rates are currently restricted to those above.
	491	+\*: Current tests reveal baud rates above 500 kbps are unstable and can cause timeouts. Please keep this in mind if using those / testing them out.
496	496
497		-====== __22. Query Firmware (**QF**)__ ======
	493	+Query Baud Rate (**QB**)
498	498
499		-Ex: #5QF<cr> might return *5QF411<cr>
	495	+Ex: #5QB<cr> might return *5QB9600<cr>
500	500
501		-The number in the reply represents the firmware version, in this example being 411.
	497	+Querying the baud rate is used simply to confirm the CB configuration command before the servo is power cycled.
502	502
503		-====== __23. Query Status (**Q**)__ ======
	499	+Configure Baud Rate (**CB**)
504	504
505		-The status query described what the servo is currently doing. The query returns an integer which must be looked up in the table below. Use the CLB advanced command to have the LED blink for certain statuses.
	501	+Important Note: the servo's current session retains the given baud rate and the new baud rate will only be in place when the servo is power cycled.
506	506
507		-Ex: #5Q<cr> might return *5Q6<cr>, which indicates the motor is holding a position.
	503	+Ex: #5CB9600<cr>
508	508
509		-|***Value returned (Q)**|**Status**|**Detailed description**
510		-|ex: *5Q0<cr>|0: Unknown|LSS is unsure / unknown state
511		-|ex: *5Q1<cr>|1: Limp|Motor driving circuit is not powered and horn can be moved freely
512		-|ex: *5Q2<cr>|2: Free moving|Motor driving circuit is not powered and horn can be moved freely
513		-|ex: *5Q3<cr>|3: Accelerating|Increasing speed from rest (or previous speed) towards travel speed
514		-|ex: *5Q4<cr>|4: Traveling|Moving at a stable speed
515		-|ex: *5Q5<cr>|5: Decelerating|Decreasing from travel speed towards final position.
516		-|ex: *5Q6<cr>|6: Holding|Keeping current position
517		-|ex: *5Q7<cr>|7: Outside limits|{More details coming soon}
518		-|ex: *5Q8<cr>|8: Stuck|Motor cannot perform request movement at current speed setting
519		-|ex: *5Q9<cr>|9: Blocked|Similar to stuck, but the motor is at maximum duty and still cannot move (i.e.: stalled)
520		-|ex: *5Q10<cr>|10: Safe Mode|(((
521		-A safety limit has been exceeded (temperature, peak current or extended high current draw).
	505	+Sending this command will change the baud rate associated with servo ID 5 to 9600 bits per second.
522	522
523		-Send a Q1 command to know which limit has been reached (described below).
524		-)))
	507	+====== __19. Gyre Rotation Direction__ ======
525	525
526		-(% class="wikigeneratedid" %)
527		-If a safety limit has been reached and exceeded, the LED will flash red and the servo will stop providing torque (no longer react to commands which cause the motor to rotate). In order to determine which limit has been reached, send a Q1 command. The servo must be RESET in order to return to normal operation, though if a limit is still detected (for example the servo is still too hot), it will revert back to Safe Mode.
	509	+"Gyre" is defined as a circular course or motion. The effect of changing the gyre direction is as if you were to use a mirror image of a circle. CW = 1; CCW = -1. The factory default is clockwise (CW).
528	528
529		-|***Value returned (Q1)**|**Status**|**Detailed description**
530		-|ex: *5Q0<cr>|No limits have been passed|Nothing is wrong
531		-|ex: *5Q1<cr>|Current limit has been passed|Something cause the current to either spike, or remain too high for too long
532		-|ex: *5Q2<cr>|Input voltage detected is below or above acceptable range|Check the voltage of your batteries or power source
533		-|ex: *5Q3<cr>|Temperature limit has been reached|The servo is too hot to continue operating safely.
	511	+{images showing before and after with AR and Origin offset}
534	534
535		-====== __24. Query Voltage (**QV**)__ ======
	513	+Query Gyre Direction (**QG**)
536	536
537		-Ex: #5QV<cr> might return *5QV11200<cr>
	515	+Ex: #5QG<cr> might return *5QG-1<cr>
538	538
539		-The number returned has one decimal, so in the case above, servo with ID 5 has an input voltage of 11.2V (perhaps a three cell LiPo battery).
	517	+The value returned above means the servo is in a counter-clockwise gyration.
540	540
541		-====== __25. Query Temperature (**QT**)__ ======
	519	+Configure Gyre (**CG**)
542	542
543		-Ex: #5QT<cr> might return *5QT564<cr>
	521	+Ex: #5CG-1<cr>
544	544
545		-The units are in tenths of degrees Celcius, so in the example above, the servo's internal temperature is 56.4 degrees C. To convert from degrees Celcius to degrees Farenheit, multiply by 1.8 and add 32. Therefore 56.4C = 133.52F.
	523	+This changes the gyre direction as described above and also writes to EEPROM.
546	546
547		-====== __26. Query Current (**QC**)__ ======
	525	+====== __20. First / Initial Position (pulse)__ ======
548	548
549		-Ex: #5QC<cr> might return *5QC140<cr>
	527	+In certain cases, a user might want to have the servo move to a specific angle upon power up. We refer to this as "first position". The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
550	550
551		-The units are in milliamps, so in the example above, the servo is consuming 140mA, or 0.14A.
	529	+Query First Position in Pulses (**QFP**)
552	552
553		-====== __27. Configure RC Mode (**CRC**)__ ======
	531	+Ex: #5QFP<cr> might return *5QFP1550<cr>
554	554
555		-This command puts the servo into RC mode (position or continuous), where it will only respond to RC pulses. Note that because this is the case, the servo will no longer accept serial commands. The servo can be placed back into smart mode by using the button menu.
	533	+The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds. If no first position has been set, servo will respond with DIS ("disabled").
556	556
557		-|**Command sent**|**Note**
558		-|ex: #5CRC1<cr>|Change to RC position mode.
559		-|ex: #5CRC2<cr>|Change to RC continuous (wheel) mode.
560		-|ex: #5CRC*<cr>|Where * is any number or value other than 1 or 2 (or no value): stay in smart mode.
	535	+Configure First Position in Pulses (**CFP**)
561	561
562		-EX: #5CRC2<cr>
	537	+Ex: #5CP1550<cr>
563	563
564		-This command would place the servo in RC wheel mode after a RESET or power cycle. Note that after a RESET or power cycle, the servo will be in RC mode and will not reply to serial commands. Using the command #5CRC<cr> or #5CRC3<cr> which requests that the servo remain in serial mode still requires a RESET command.
	539	+This configuration command means the servo, when set to RC mode, will immediately move to an angle equivalent to having received an RC pulse of 1550 microseconds upon power up. Sending a CFP command without a number results in the servo remaining limp upon power up (i.e. disabled).
565	565
566		-Important note:** **To revert from RC mode back to serial mode, the [[LSS - Button Menu>>doc:lynxmotion-smart-servo.lss-button-menu.WebHome]] is required. Should the button be inaccessible (or broken) when the servo is in RC mode and the user needs to change to serial mode, a 5V constant HIGH needs to be sent to the servo's Rx pin (RC PWM pin), ensuring a common GND and wait for 30 seconds. Normal RC PWM pulses should not exceed 2500 milliseconds. After 30 seconds, the servo will interpret this as a desired mode change and change to serial mode. This has been implemented as a fail safe.
	541	+====== __21. First / Initial Position (Degrees)__ ======
567	567
568		-====== __28. **RESET**__ ======
	543	+In certain cases, a user might want to have the servo move to a specific angle upon power up. We refer to this as "first position". The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
569	569
570		-Ex: #5RESET<cr> or #5RS<cr>
	545	+Query First Position in Degrees (**QFD**)
571	571
572		-This command does a "soft reset" (no power cycle required) and reverts all commands to those stored in EEPROM (i.e. configuration commands).
	547	+Ex: #5QFD<cr> might return *5QFD64<cr>
573	573
574		-====== __29. **DEFAULT** & CONFIRM__ ======
	549	+The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds.
575	575
576		-Ex: #5DEFAULT<cr>
	551	+Configure First Position in Degrees (**CFD**)
577	577
578		-This command sets in motion the reset of all values to the default values included with the version of the firmware installed on that servo. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the DEFAULT function.
	553	+Ex: #5CD64<cr>
579	579
580		-EX: #5DEFAULT<cr> followed by #5CONFIRM<cr>
	555	+This configuration command means the servo, when set to smart mode, will immediately move to 6.4 degrees upon power up. Sending a CFD command without a number results in the servo remaining limp upon power up.
581	581
582		-Since it it not common to have to restore all configurations, a confirmation command is needed after a firmware command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will exit the command.
	557	+====== __22. Query Target Position in Degrees (**QDT**)__ ======
583	583
584		-Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
	559	+Ex: #5QDT<cr> might return *5QDT6783<cr>
585	585
586		-====== __30. **UPDATE** & CONFIRM__ ======
	561	+The query target position command returns the target angle during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond without a number (Ex: *5QDT<cr>).
587	587
588		-Ex: #5UPDATE<cr>
	563	+====== __23. Query Model String (**QMS**)__ ======
589	589
590		-This command sets in motion the equivalent of a long button press when the servo is not powered in order to enter firmware update mode. This is useful should the button be broken or inaccessible. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the UPDATE function.
	565	+Ex: #5QMS<cr> might return *5QMSLSS-HS1cr>
591	591
592		-EX: #5UPDATE<cr> followed by #5CONFIRM<cr>
	567	+This reply means the servo model is LSS-HS1, meaning a high speed servo, first revision.
593	593
594		-Since it it not common to have to update firmware, a confirmation command is needed after an UPDATE command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
	569	+====== __23b. Query Model (**QM**)__ ======
595	595
596		-Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
	571	+Ex: #5QM<cr> might return *5QM68702699520cr>
597	597
598		-= Advanced =
	573	+This reply means the servo model is 0xFFF000000 or 100, meaning a high speed servo, first revision.
599	599
600		-The motion controller used in serial mode is not the same as the motion controller use in RC mode. RC mode is intended to add functionality to what would be considered "normal" RC behavior based on PWM input.
	575	+====== __24. Query Serial Number (**QN**)__ ======
601	601
602		-====== __A1. Angular Stiffness (**AS**)__ ======
	577	+Ex: #5QN<cr> might return *5QN~_~_<cr>
603	603
604		-The servo's rigidity / angular stiffness can be thought of as (though not identical to) a damped spring in which the value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes. There are no units.
	579	+The number in the response is the servo's serial number which is set and cannot be changed.
605	605
606		-A positive value of "angular stiffness":
	581	+====== __25. Query Firmware (**QF**)__ ======
607	607
608		-* The more torque will be applied to try to keep the desired position against external input / changes
609		-* The faster the motor will reach its intended travel speed and the motor will decelerate faster and nearer to its target position
	583	+Ex: #5QF<cr> might return *5QF11<cr>
610	610
611		-A negative value on the other hand:
	585	+The integer in the reply represents the firmware version with one decimal, in this example being 1.1
612	612
613		-* Causes a slower acceleration to the travel speed, and a slower deceleration
614		-* Allows the target position to deviate more from its position before additional torque is applied to bring it back
	587	+====== __26. Query Status (**Q**)__ ======
615	615
616		-The default value for stiffness depending on the firmware may be 0 or 1. Greater values produce increasingly erratic behavior and the effect becomes extreme below -4 and above +4. Maximum values are -10 to +10.
	589	+Ex: #5Q<cr> might return *5Q6<cr>, which indicates the motor is holding a position.
617	617
618		-Ex: #5AS-2<cr>
	591	+|*Value returned|**Status**|**Detailed description**
	592	+|ex: *5Q0<cr>|Unknown|LSS is unsure
	593	+|ex: *5Q1<cr>|Limp|Motor driving circuit is not powered and horn can be moved freely
	594	+|ex: *5Q2<cr>|Free moving|Motor driving circuit is not powered and horn can be moved freely
	595	+|ex: *5Q3<cr>|Accelerating|Increasing speed from rest (or previous speeD) towards travel speed
	596	+|ex: *5Q4<cr>|Traveling|Moving at a stable speed
	597	+|ex: *5Q5<cr>|Decelerating|Decreasing from travel speed towards final position.
	598	+|ex: *5Q6<cr>|Holding|Keeping current position
	599	+|ex: *5Q7<cr>|Stepping|Special low speed mode to maintain torque
	600	+|ex: *5Q8<cr>|Outside limits|{More details coming soon}
	601	+|ex: *5Q9<cr>|Stuck|Motor cannot perform request movement at current speed setting
	602	+|ex: *5Q10<cr>|Blocked|Similar to stuck, but the motor is at maximum duty and still cannot move (i.e.: stalled)
619	619
620		-This reduces the angular stiffness to -2 for that session, allowing the servo to deviate more around the desired position. This can be beneficial in many situations such as impacts (legged robots) where more of a "spring" effect is desired. Upon reset, the servo will use the value stored in memory, based on the last configuration command.
	604	+====== __27. Query Voltage (**QV**)__ ======
621	621
622		-Ex: #5QAS<cr>
	606	+Ex: #5QV<cr> might return *5QV11200<cr>
623	623
624		-Queries the value being used.
	608	+The number returned has one decimal, so in the case above, servo with ID 5 has an input voltage of 11.2V (perhaps a three cell LiPo battery).
625	625
626		-Ex: #5CAS<cr>
	610	+====== __28. Query Temperature (**QT**)__ ======
627	627
628		-Writes the desired angular stiffness value to memory.
	612	+Ex: #5QT<cr> might return *5QT564<cr>
629	629
630		-====== __A2. Angular Holding Stiffness (**AH**)__ ======
	614	+The units are in tenths of degrees Celcius, so in the example above, the servo's internal temperature is 56.4 degrees C. To convert from degrees Celcius to degrees Farenheit, multiply by 1.8 and add 32. Therefore 56.4C = 133.52F.
631	631
632		-The angular holding stiffness determines the servo's ability to hold a desired position under load. The default value for stiffness depending on the firmware may be 0 or 1. Greater values produce increasingly erratic behavior and the effect becomes extreme below -4 and above +4. Maximum values are -10 to +10. Note that when  considering altering a stiffness value, the end effect depends on the mode being tested.
	616	+====== __29. Query Current (**QC**)__ ======
633	633
634		-Ex: #5AH3<cr>
	618	+Ex: #5QC<cr> might return *5QC140<cr>
635	635
636		-This sets the holding stiffness for servo #5 to 3 for that session.
	620	+The units are in milliamps, so in the example above, the servo is consuming 140mA, or 0.14A.
637	637
638		-Query Angular Hold Stiffness (**QAH**)
	622	+====== __30. RC Mode (**CRC**)__ ======
639	639
640		-Ex: #5QAH<cr> might return *5QAH3<cr>
	624	+This command puts the servo into RC mode (position or continuous), where it will only respond to RC pulses. Note that because this is the case, the servo will no longer accept serial commands. The servo can be placed back into smart mode by using the button menu.
641	641
642		-This returns the servo's angular holding stiffness value.
	626	+|**Command sent**|**Note**
	627	+|ex: #5CRC<cr>|Stay in smart mode.
	628	+|ex: #5CRC1<cr>|Change to RC position mode.
	629	+|ex: #5CRC2<cr>|Change to RC continuous (wheel) mode.
	630	+|ex: #5CRC*<cr>|Where * is any number or value. Stay in smart mode.
643	643
644		-Configure Angular Hold Stiffness (**CAH**)
	632	+EX: #5CRC<cr>
645	645
646		-Ex: #5CAH2<cr>
	634	+====== __31. RESET__ ======
647	647
648		-This writes the angular holding stiffness of servo #5 to 2 to EEPROM. Note that when  considering altering a stiffness value, the end effect depends on the mode being tested.
	636	+Ex: #5RESET<cr> or #5RS<cr>
649	649
650		-====== __A3: Angular Acceleration (**AA**)__ ======
	638	+This command does a "soft reset" (no power cycle required) and reverts all commands to those stored in EEPROM (i.e. configuration commands).
651	651
652		-The default value for angular acceleration is 100, which is the same as the maximum deceleration. Accepts values of between 1 and 100. Increments of 10 degrees per second squared.
	640	+====== __32. DEFAULT & CONFIRM__ ======
653	653
654		-Ex: #5AA30<cr>
	642	+Ex: #5DEFAULT<cr>
655	655
656		-Query Angular Acceleration (**QAD**)
	644	+This command sets in motion the reset all values to the default values included with the version of the firmware installed on that servo. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the DEFAULT function.
657	657
658		-Ex: #5QA<cr> might return *5QA30<cr>
	646	+EX: #5DEFAULT<cr> followed by #5CONFIRM<cr>
659	659
660		-Configure Angular Acceleration (**CAD**)
	648	+Since it it not common to have to restore all configurations, a confirmation command is needed after a firmware command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
661	661
662		-Ex: #5CA30<cr>
	650	+Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
663	663
664		-====== __A4: Angular Deceleration (**AD**)__ ======
	652	+====== __33. UPDATE & CONFIRM__ ======
665	665
666		-The default value for angular deceleration is 100, which is the same as the maximum acceleration. Values between 1 and 15 have the greatest impact.
	654	+Ex: #5UPDATE<cr>
667	667
668		-Ex: #5AD8<cr>
	656	+This command sets in motion the equivalent of a long button press when the servo is not powered in order to enter firmware update mode. This is useful should the button be broken or inaccessible. The servo then waits for the CONFIRM command. Any other command received will cause the servo to exit the UPDATE function.
669	669
670		-Query Angular Deceleration (**QAD**)
	658	+EX: #5UPDATE<cr> followed by #5CONFIRM<cr>
671	671
672		-Ex: #5QD<cr> might return *5QD8<cr>
	660	+Since it it not common to have to update firmware, a confirmation command is needed after an UPDATE command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
673	673
674		-Configure Angular Deceleration (**CAD**)
675		-
676		-Ex: #5CD8<cr>
677		-
678		-====== __A5: Motion Control (**EM**)__ ======
679		-
680		-The command EM0 disables use of the motion controller (acceleration, velocity / travel, deceleration). As such, the servo will move at full speed for all motion commands. The command EM1 enables use of the motion controller.
681		-
682		-Note that if the modifiers S or T are used, it is assumed that motion control is desired, and for that command, EM1 will be used.
683		-
684		-====== __A6. Configure LED Blinking (**CLB**)__ ======
685		-
686		-This command allows you to control when the RGB LED will blink the user set color (see [[16. RGB LED>>||anchor="H16.RGBLED28LED29"]] for details). This is very useful when visually seeing what the servo is doing. You can turn on or off blinking for various LSS status. The command requires that the servo be RESET. Here is the list and their associated value:
687		-
688		-(% style="width:195px" %)
689		-|(% style="width:134px" %)**Blink While:**|(% style="width:58px" %)**#**
690		-|(% style="width:134px" %)No blinking|(% style="width:58px" %)0
691		-|(% style="width:134px" %)Limp|(% style="width:58px" %)1
692		-|(% style="width:134px" %)Holding|(% style="width:58px" %)2
693		-|(% style="width:134px" %)Accelerating|(% style="width:58px" %)4
694		-|(% style="width:134px" %)Decelerating|(% style="width:58px" %)8
695		-|(% style="width:134px" %)Free|(% style="width:58px" %)16
696		-|(% style="width:134px" %)Travelling|(% style="width:58px" %)32
697		-|(% style="width:134px" %)Always blink|(% style="width:58px" %)63
698		-
699		-To set blinking, use CLB with the value of your choosing. To activate blinking in multiple status, simply add together the values of the corresponding status. See examples below:
700		-
701		-Ex: #5CLB0<cr> to turn off all blinking (LED always solid)
702		-Ex: #5CLB1<cr> only blink when limp (1)
703		-Ex: #5CLB2<cr> only blink when holding (2)
704		-Ex: #5CLB12<cr> only blink when accel or decel (accel 4 + decel 8 = 12)
705		-Ex: #5CLB48<cr> only blink when free or travel (free 16 + travel 32 = 48)
706		-Ex: #5CLB63<cr> blink in all status (1 + 2 + 4 + 8 + 16 + 32)
707		-
708		-RESETTING the servo is needed.
	662	+Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.

XWiki.XWikiRights[0]

Allow/Deny

...	...	@@ -1,0 +1,1 @@
	1	+Allow

Groups

...	...	@@ -1,0 +1,1 @@
	1	+xwiki:XWiki.XWikiAdminGroup

Levels

...	...	@@ -1,0 +1,1 @@
	1	+view

XWiki.XWikiRights[1]

Allow/Deny

...	...	@@ -1,0 +1,1 @@
	1	+Allow

Groups

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.XWikiAdminGroup

Levels

...	...	@@ -1,0 +1,1 @@
	1	+view

XWiki.XWikiRights[2]

Allow/Deny

...	...	@@ -1,0 +1,1 @@
	1	+Allow

Groups

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Profiles (Lynxmotion).BETA Testers

Levels

...	...	@@ -1,0 +1,1 @@
	1	+view