Changes for page LSS Communication Protocol

Last modified by Eric Nantel on 2025/06/06 07:47

From version < 16.1 >

edited by Coleman Benson
on 2018/04/13 16:11

To version < 12.1 >

edited by Coleman Benson
on 2018/04/04 12:36

< >

Change comment: There is no comment for this version

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -42,28
          +42,6 @@
  Modified commands are command specific.
  )))
--(((
--
--)))
--
--== Configuration Commands ==
--
--Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:Lynxmotion Smart Servos (LSS).LSS - RC PWM.WebHome]].
--
--1. Start with a number sign # (U+0023)
--1. Servo ID number as an integer
--1. Configuration command (two to three letters, no spaces, capital or lower case)
--1. Configuration value in the correct units with no decimal
--1. End with a control / carriage return '<cr>'
--
--Ex: #5CO-50<cr>
--
--Assigns an absolute origin offset of -5.0 degrees (with respect to factory origin) to servo #5 and changes the offset for that session to -5.0 degrees.
--
--Configuration commands are not cumulative, in that if two configurations are sent at any time, only the last configuration is used and stored.
--
--*Important Note: the one exception is the baud rate - the servo's current session retains the given baud rate. The new baud rate will only be in place when the servo is power cycled.
--
  == Query Commands ==
  Query commands are sent serially to the servo's Rx pin and must be set in the following format:
@@ -91,21
          +91,25 @@
  )))
  Indicates that servo #5 is currently at 144.3 degrees.
++)))
--**Session vs Configuration Query**
++== Configuration Commands ==
--By default, the query command returns the sessions' value; should no action commands have been sent to change, it will return the value saved in EEPROM from the last configuration command.
++Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:Lynxmotion Smart Servos (LSS).LSS - RC PWM.WebHome]].
--In order to query the value in EEPROM, add a '1' to the query command.
++1. Start with a number sign # (U+0023)
++1. Servo ID number as an integer
++1. Configuration command (two to three letters, no spaces, capital or lower case)
++1. Configuration value in the correct units with no decimal
++1. End with a control / carriage return '<cr>'
--Ex: #5CSR20<cr> sets the maximum speed for servo #5 to 20rpm upon RESET (explained below).
++Ex: #5CO-50<cr>
--After RESET: #5SR4<cr> sets the session's speed to 4rpm.
++Assigns an absolute origin offset of -5.0 degrees (with respect to factory origin) to servo #5 and changes the offset for that session to -5.0 degrees.
--#5QSR<cr> would return *5QSR4<cr> which represents the value for that session.
++Configuration commands are not cumulative, in that if two configurations are sent at any time, only the last configuration is used and stored.
--#5QSR1<cr> would return *5QSR20<cr> which represents the value in EEPROM
--)))
++*Important Note: the one exception is the baud rate - the servo's current session retains the given baud rate. The new baud rate will only be in place when the servo is power cycled.
  = Command List =
@@ -125,8
          +125,8 @@
  | 11|**W**heel mode in **R**PM| WR| QWR| | | ✓| rpm|
  | 12|**S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|
  | 13|**S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|
--| 14|**R**igidity| R| QR| CR| ✓| ✓|none|
--| 15|//N/A (removed)//| | | | | | |
++| 14|**A**ngular **A**cceleration| AA| QAA| CAA| ✓| ✓| tenths of degrees per second squared|
++| 15|**A**ngular **D**eceleration| AD| QAD| CAD| ✓| ✓| tenths of degrees per second squared|
  | 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6= 7=MAGENTA, 8=WHITE
  | 17|**ID** #| ID| QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to.
  | 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
@@ -309,38
          +309,46 @@
  Using the CSD command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSD value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
--__14. Rigidity (R)__
++__14. Angular Acceleration (**AA**)__
--The servo's rigidity can be thought of as (though not identical to) a damped spring in which the rigidity value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes.
++{More information coming soon}
--A positive value of "rigidity":
++Ex:
--* The more torque will be applied to try to keep the desired position against external input / changes
--* The faster the motor will reach its intended travel speed and the motor will decelerate faster and nearer to its target position
++{Description coming soon}
--A negative value on the other hand:
++Query Angular Acceleration (**QAA**)
--* Causes a slower acceleration to the travel speed, and a slower deceleration
--* Allows the target position to deviate more from its position before additional torque is applied to bring it back
++Ex:
--The default value is zero and the effect becomes extreme by -4, +4. There are no units, only integers between -4 to 4. Greater values produce increasingly erratic behavior.
++{Description coming soon}
--Ex: #5R-2<cr>
++Configure Angular Acceleration (**CAA**)
--This reduces the rigidity to -2 for that session, allowing the servo to deviate more around the desired position. This can be beneficial in many situations such as impacts (legged robots) where more of a "spring" effect is desired. Upon reset, the servo will use the value stored in memory, based on the last configuration command.
++Ex:
--Ex: #5QR<cr>
++{Description coming soon}
--Queries the value being used.
++__15. Angular Deceleration (**AD**)__
--Ex: #5CR<cr>
++{More information coming soon}
--Writes the desired rigidity value to memory.
++Ex:
--__15. N/A (removed)__
++{Description coming soon}
--This command has been removed.
++Query Angular Acceleration (**QAD**)
++Ex:
++
++{Description coming soon}
++
++Configure Angular Acceleration (**CAD**)
++
++Ex:
++
++{Description coming soon}
++
  __16. RGB LED (**LED**)__
  Ex: #5LED3<cr>
@@ -505,8
          +505,6 @@
  Since it it not common to have to restore all configurations, a confirmation command is needed after a firmware command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
--Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
--
  **__UPDATE __**__& **CONFIRM**__
  Ex: #5UPDATE<cr>
@@ -517,8
          +517,6 @@
  Since it it not common to have to update firmware, a confirmation command is needed after an UPDATE command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
--Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
--
  === Virtual Angular Position ===
  {In progress}

Changes for page LSS Communication Protocol

Summary

Details

Navigation