Changes for page LSS Communication Protocol

Last modified by Eric Nantel on 2025/06/06 07:47

From version < 208.2 >

edited by Eric Nantel
on 2022/05/10 15:18

To version < 191.1 >

edited by Coleman Benson
on 2020/05/01 13:10

< >

Change comment: There is no comment for this version

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1
          +1,1 @@
--xwiki:XWiki.ENantel
++xwiki:XWiki.CBenson

Content

@@ -7,7
          +7,7 @@
  The Lynxmotion Smart Servo (LSS) serial protocol was created in order to be as simple and straightforward as possible from a user perspective ("human readable format"), while at the same time staying compact and robust yet highly versatile. The protocol was based on Lynxmotion's SSC-32 & SSC-32U RC servo controllers and almost everything one might expect to be able to configure for a smart servomotor is available.
--In order to be able to control each servo individually with commands, the first step should be to assign a different ID number to each servo (see details on the Configure ID, or "CID" command [[here>>doc:||anchor="HIdentificationNumber28ID29"]]). Only the servo(s) which have been configured to a specific ID will act on a command sent to that ID. There is currently no CRC or checksum implemented as part of the protocol.
++In order to be able to control each servo individually with commands, the first step should be to assign a different ID number to each servo (see details on CID [[here>>doc:||anchor="HIdentificationNumber28ID29"]]). Once this has been done, only the servo(s) which have been assigned to the ID sent as part of the command will follow that command. There is currently no CRC or checksum implemented as part of the protocol.
  == Session ==
@@ -15,21
          +15,21 @@
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
  A "session" is defined as the time between when the servo is powered ON to when it is powered OFF or reset.<div class="wikimodel-emptyline"></div>
--**Note 1:** For a given session, the action related to a specific command overrides the stored value in EEPROM.<div class="wikimodel-emptyline"></div>
--**Note 2:** During the power-on / reset process the LSS cannot accept commands for a small amount of time (~1.25 s).<div class="wikimodel-emptyline"></div>
--**Note 3:** You can ensure the LSS is ready by using a query command to check for response (ex: #[id]Q\r or #[id]QID\r described below). If the LSS is ready for commands (initialized) it will respond to the query. A timeout between 50-100 ms is recommended to compensate for drivers, OS and buffering delays.
++**Note #1:** For a given session, the action related to a specific command overrides the stored value in EEPROM.<div class="wikimodel-emptyline"></div>
++**Note #2:** During the power-on / reset process the LSS cannot accept commands for a small amount of time (1.25 s).<div class="wikimodel-emptyline"></div>
++You can ensure the LSS is ready by using a query command to check for response (ex: #[id]Q\r or #[id]QID\r). If the LSS is ready for commands (initialized) it will respond to the query. A timeout between 50-100 ms is recommended to compensate for drivers, OS and buffering delays.
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
  == Action Commands ==
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
--Action commands tell the servo, within that session, to do something (i.e. "take an action"). The types of action commands which can be sent are described below, and they cannot be combined with other commands such as queries or configurations. Only one action command can be sent at a time. Action commands are session-specific, therefore once a servo is power cycled, it will not have any "memory" of previous actions or [[virtual positions>>||anchor="HVirtualAngularPosition"]] (described below). Action commands are sent serially to the servo's Rx pin and must be sent in the following format:<div class="wikimodel-emptyline"></div>
++Action commands tell the servo, within that session, to do something (i.e. "take an action"). The types of action commands which can be sent are described below, and they cannot be combined with other commands such as queries or configurations. Only one action command can be sent at a time. Action commands are session-specific, therefore once a servo is power cycled, it will not have any "memory" of previous actions or [[virtual positions>>||anchor="HVirtualAngularPosition"]]. Action commands are sent serially to the servo's Rx pin and must be sent in the following format:<div class="wikimodel-emptyline"></div>
 . Start with a number sign **#** (Unicode Character: U+0023)
--1. Servo ID number as an integer (assigning an ID described below)
--1. Action command (one or more letters, no whitespace, capital or lowercase from the list below)
++1. Servo ID number as an integer
++1. Action command (one or more letters, no whitespace, capital or lower case)
 . Action value in the correct units with no decimal
 . End with a carriage return **&#92;r** or **&lt;cr&gt;** Unicode Character (U+000D)
@@ -42,15
          +42,15 @@
  == Modifiers ==
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
  Modifiers can only be used with certain **action commands**. The format to include a modifier is:<div class="wikimodel-emptyline"></div>
 . Start with a number sign **#** (Unicode Character: U+0023)
 . Servo ID number as an integer
--1. Action command (one to three letters, no spaces, capital or lowercase from a subset of action commands below)
++1. Action command (one to three letters, no spaces, capital or lower case)
 . Action value in the correct units with no decimal
--1. Modifier command (one or two letters from  the list of modifiers below)
++1. Modifier command (one letter to too letters)
 . Modifier value in the correct units with no decimal
 . End with a carriage return **&#92;r** or **&lt;cr&gt;** Unicode Character (U+000D)
@@ -62,7
          +62,7 @@
  == Query Commands ==
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
  Query commands request information from the servo. They are received via the Rx pin of the servo, and the servo's reply is sent via the servo's Tx pin. Using separate lines for Tx and Rx is called "full duplex". Query commands are also similar to action and configuration commands and must use the following format:<div class="wikimodel-emptyline"></div>
@@ -71,7
          +71,7 @@
 . Query command (one to four letters, no spaces, capital or lower case)
 . End with a carriage return **&#92;r** or **&lt;cr&gt;** Unicode Character (U+000D)<div class="wikimodel-emptyline"></div>
--Ex: #5QD&lt;cr&gt; Query the position in (tenth of) degrees for servo with ID #5<div class="wikimodel-emptyline"></div>
++Ex: #5QD&lt;cr&gt; Query position in (tenth of) degrees for servo #5<div class="wikimodel-emptyline"></div>
  The query will return a serial string (almost instantaneously) via the servo's Tx pin with the following format:
@@ -91,11
          +91,11 @@
  == Configuration Commands ==
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
  Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM.<div class="wikimodel-emptyline"></div>
--These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session. Not all action commands have a corresponding configuration command and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:lynxmotion-smart-servo.lss-radio-control-pwm.WebHome]]. Configuration commands are not cumulative. This means that if two of the same configuration commands are sent, one after the next, only the last configuration is used and stored.<div class="wikimodel-emptyline"></div>
++These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not. In the Command table below, the column "Session" denotes if the configuration command affects the session. Not all action commands have a corresponding configuration command and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:lynxmotion-smart-servo.lss-radio-control-pwm.WebHome]]. Configuration commands are not cumulative. This means that if two same configuration commands are sent, one after the next, only the last configuration is used and stored.<div class="wikimodel-emptyline"></div>
  The format to send a configuration command is identical to that of an action command:<div class="wikimodel-emptyline"></div>
@@ -153,71
          +153,75 @@
  **Latest firmware version currently : 368.29.14**
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**Communication Setup**>>||anchor="HCommunicationSetup"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**Communication Setup**>>||anchor="COMMUNICATION_SETUP"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Action**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[**Reset**>>||anchor="HReset"]]|(% style="text-align:center" %)RESET|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Soft reset. See command for details.
--| |[[**Default** Configuration>>||anchor="HDefault26confirm"]]|(% style="text-align:center" %)DEFAULT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Revert to firmware default values. See command for details
--| |[[Firmware **Update** Mode>>||anchor="HUpdate26confirm"]]|(% style="text-align:center" %)UPDATE|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Update firmware. See command for details.
--| |[[**Confirm** Changes>>||anchor="HConfirm"]]|(% style="text-align:center" %)CONFIRM|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
--| |[[**C**hange to **RC**>>||anchor="HConfigureRCMode28CRC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)CRC|(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Change to RC mode 1 (position) or 2 (wheel).
--| |[[**ID** #>>||anchor="HIdentificationNumber28ID29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QID|(% style="text-align:center" %)CID|(% style="text-align:center" %) |(% style="text-align:center" %)✓|0| |Reset required after change. ID 254 is a "broadcast" which all servos respond to.
--| |[[**B**audrate>>||anchor="HBaudRate"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QB|(% style="text-align:center" %)CB|(% style="text-align:center" %) |(% style="text-align:center" %)✓|115200| |Reset required after change.
++| |[[**Reset**>>||anchor="RESET"]]|(% style="text-align:center" %)RESET|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Soft reset. See command for details.
++| |[[**Default** Configuration>>||anchor="DEFAULT"]]|(% style="text-align:center" %)DEFAULT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Revert to firmware default values. See command for details
++| |[[Firmware **Update** Mode>>||anchor="UPDATE_CONFIRM"]]|(% style="text-align:center" %)UPDATE|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Update firmware. See command for details.
++| |[[**Confirm** Changes>>||anchor="CONFIRM"]]|(% style="text-align:center" %)CONFIRM|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
++| |[[**C**hange to **RC**>>||anchor="CHANGE_RC"]]|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)CRC|(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Change to RC mode 1 (position) or 2 (wheel).
++| |[[**ID** #>>||anchor="ID"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QID|(% style="text-align:center" %)CID|(% style="text-align:center" %) |(% style="text-align:center" %)✓|0| |Reset required after change. ID 254 is a "broadcast" which all servos respond to.
++| |[[**B**audrate>>||anchor="BAUDRATE"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QB|(% style="text-align:center" %)CB|(% style="text-align:center" %) |(% style="text-align:center" %)✓|115200| |Reset required after change.
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**Motion**>>||anchor="HMotion"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**Motion**>>||anchor="MOTION"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Action**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[Position in **D**egrees>>||anchor="HPositioninDegrees28D29"]]|(% style="text-align:center" %)D|(% style="text-align:center" %)QD/QDT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°|
--| |[[**M**ove in **D**egrees (relative)>>||anchor="H28Relative29MoveinDegrees28MD29"]]|(% style="text-align:center" %)MD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°|
--| |[[**W**heel mode in **D**egrees>>||anchor="HWheelModeinDegrees28WD29"]]|(% style="text-align:center" %)WD|(% style="text-align:center" %)QWD/QVT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |°/s|A.K.A. "Speed mode" or "Continuous rotation"
--| |[[**W**heel mode in **R**PM>>||anchor="HWheelModeinRPM28WR29"]]|(% style="text-align:center" %)WR|(% style="text-align:center" %)QWR|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |RPM|A.K.A. "Speed mode" or "Continuous rotation"
--| |[[Position in **P**WM>>||anchor="HPositioninPWM28P29"]]|(% style="text-align:center" %)P|(% style="text-align:center" %)QP|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |us|Inherited from SSC-32 serial protocol
--| |[[**M**ove in PWM (relative)>>||anchor="H28Relative29MoveinPWM28M29"]]|(% style="text-align:center" %)M|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |us|
--| |[[**R**aw **D**uty-cycle **M**ove>>||anchor="HRawDuty-cycleMove28RDM29"]]|(% style="text-align:center" %)RDM|(% style="text-align:center" %)QMD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |-1023 to 1023 integer|Positive values : CW / Negative values : CCW
--| |[[**Q**uery Status>>||anchor="HQueryStatus28Q29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)Q|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1 to 8 integer|See command description for details
--| |[[**L**imp>>||anchor="HLimp28L29"]]|(% style="text-align:center" %)L|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
--| |[[**H**alt & Hold>>||anchor="HHalt26Hold28H29"]]|(% style="text-align:center" %)H|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
++| |[[Position in **D**egrees>>||anchor="POSITION_D"]]|(% style="text-align:center" %)D|(% style="text-align:center" %)QD/QDT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°|
++| |[[**M**ove in **D**egrees (relative)>>||anchor="MOVE_D"]]|(% style="text-align:center" %)MD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°|
++| |[[**W**heel mode in **D**egrees>>||anchor="WHEEL_D"]]|(% style="text-align:center" %)WD|(% style="text-align:center" %)QWD/QVT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |°/s|A.K.A. "Speed mode" or "Continuous rotation"
++| |[[**W**heel mode in **R**PM>>||anchor="WHEEL_RPM"]]|(% style="text-align:center" %)WR|(% style="text-align:center" %)QWR|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |RPM|A.K.A. "Speed mode" or "Continuous rotation"
++| |[[Position in **P**WM>>||anchor="POSITION_PWM"]]|(% style="text-align:center" %)P|(% style="text-align:center" %)QP|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |us|Inherited from SSC-32 serial protocol
++| |[[**M**ove in PWM (relative)>>||anchor="MOVE_PWM"]]|(% style="text-align:center" %)M|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |us|
++| |[[**R**aw **D**uty-cycle **M**ove>>||anchor="MOVE_RAW"]]|(% style="text-align:center" %)RDM|(% style="text-align:center" %)QMD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |-1023 to 1023 integer|Positive values : CW / Negative values : CCW
++| |[[**Q**uery Status>>||anchor="QUERY_STATUS"]]|(% style="text-align:center" %) |(% style="text-align:center" %)Q|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1 to 8 integer|See command description for details
++| |[[**L**imp>>||anchor="LIMP"]]|(% style="text-align:center" %)L|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
++| |[[**H**alt & Hold>>||anchor="HALT_HOLD"]]|(% style="text-align:center" %)H|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**Motion Setup**>>||anchor="HMotionSetup"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**Motion Setup**>>||anchor="MOTION_SETUP"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Action**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[**E**nable **M**otion Profile>>||anchor="HEnableMotionProfile28EM29"]]|(% style="text-align:center" %)EM|(% style="text-align:center" %)QEM|(% style="text-align:center" %)CEM|(% style="text-align:center" %) |(% style="text-align:center" %)✓|1| |EM1: trapezoidal motion profile / EM0: no motion profile
--| |[[**F**ilter **P**osition **C**ount>>||anchor="HFilterPositionCount28FPC29"]]|(% style="text-align:center" %)FPC|(% style="text-align:center" %)QFPC|(% style="text-align:center" %)CFPC|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|5| |Affects motion only when motion profile is disabled (EM0)
--| |[[**O**rigin Offset>>||anchor="HOriginOffset28O29"]]|(% style="text-align:center" %)O|(% style="text-align:center" %)QO|(% style="text-align:center" %)CO|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|0|1/10°|
--| |[[**A**ngular **R**ange>>||anchor="HAngularRange28AR29"]]|(% style="text-align:center" %)AR|(% style="text-align:center" %)QAR|(% style="text-align:center" %)CAR|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|1800|1/10°|
--| |[[**A**ngular **S**tiffness>>||anchor="HAngularStiffness28AS29"]]|(% style="text-align:center" %)AS|(% style="text-align:center" %)QAS|(% style="text-align:center" %)CAS|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|0|-4 to +4 integer|Suggested values are between 0 to +4
--| |[[**A**ngular **H**olding Stiffness>>||anchor="HAngularHoldingStiffness28AH29"]]|(% style="text-align:center" %)AH|(% style="text-align:center" %)QAH|(% style="text-align:center" %)CAH|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|4|-10 to +10 integer|
--| |[[**A**ngular **A**cceleration>>||anchor="HAngularAcceleration28AA29"]]|(% style="text-align:center" %)AA|(% style="text-align:center" %)QAA|(% style="text-align:center" %)CAA|(% style="text-align:center" %) |(% style="text-align:center" %)✓|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).
--| |[[**A**ngular **D**eceleration>>||anchor="HAngularDeceleration28AD29"]]|(% style="text-align:center" %)AD|(% style="text-align:center" %)QAD|(% style="text-align:center" %)CAD|(% style="text-align:center" %) |(% style="text-align:center" %)✓|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).
--| |[[**G**yre Direction>>||anchor="HGyreDirection28G29"]]|(% style="text-align:center" %)G|(% style="text-align:center" %)QG|(% style="text-align:center" %)CG|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|1| |Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)
--| |[[**F**irst Position (**D**eg)>>||anchor="HFirstPosition"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QFD|(% style="text-align:center" %)CFD|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|No value|1/10°|Reset required after change.
--| |[[**M**aximum **M**otor **D**uty>>||anchor="HMaximumMotorDuty28MMD29"]]|(% style="text-align:center" %)MMD|(% style="text-align:center" %)QMMD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓|1023|255 to 1023 integer|
--| |[[Maximum **S**peed in **D**egrees>>||anchor="HMaximumSpeedinDegrees28SD29"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %)QSD|(% style="text-align:center" %)CSD|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|Max|0.1°/s|SD overwrites SR / CSD overwrites CSR and vice-versa
--| |[[Maximum **S**peed in **R**PM>>||anchor="HMaximumSpeedinRPM28SR29"]]|(% style="text-align:center" %)SR|(% style="text-align:center" %)QSR|(% style="text-align:center" %)CSR|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|Max|RPM|SD overwrites SR / CSD overwrites CSR and vice-versa
++| |[[**E**nable **M**otion Profile>>||anchor="MOTION_PROFILE"]]|(% style="text-align:center" %)EM|(% style="text-align:center" %)QEM|(% style="text-align:center" %)CEM|(% style="text-align:center" %) |(% style="text-align:center" %)✓|1| |EM1: trapezoidal motion profile / EM0: no motion profile
++| |[[**F**ilter **P**osition **C**ount>>||anchor="FILTER_POSITION_COUNT"]]|(% style="text-align:center" %)FPC|(% style="text-align:center" %)QFPC|(% style="text-align:center" %)CFPC|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|5| |Affects motion only when motion profile is disabled (EM0)
++| |[[**O**rigin Offset>>||anchor="ORIGIN_OFFSET"]]|(% style="text-align:center" %)O|(% style="text-align:center" %)QO|(% style="text-align:center" %)CO|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|0|1/10°|
++| |[[**A**ngular **R**ange>>||anchor="ANGULAR_RANGE"]]|(% style="text-align:center" %)AR|(% style="text-align:center" %)QAR|(% style="text-align:center" %)CAR|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|1800|1/10°|
++| |[[**A**ngular **S**tiffness>>||anchor="ANGULAR_STIFFNESS"]]|(% style="text-align:center" %)AS|(% style="text-align:center" %)QAS|(% style="text-align:center" %)CAS|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|0|-4 to +4 integer|Suggested values are between 0 to +4
++| |[[**A**ngular **H**olding Stiffness>>||anchor="ANGULAR_HOLDING_STIFFNESS"]]|(% style="text-align:center" %)AH|(% style="text-align:center" %)QAH|(% style="text-align:center" %)CAH|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|4|-10 to +10 integer|
++| |[[**A**ngular **A**cceleration>>||anchor="ANGULAR_ACCELERATION"]]|(% style="text-align:center" %)AA|(% style="text-align:center" %)QAA|(% style="text-align:center" %)CAA|(% style="text-align:center" %) |(% style="text-align:center" %)✓|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).
++| |[[**A**ngular **D**eceleration>>||anchor="ANGULAR_DECELERATION"]]|(% style="text-align:center" %)AD|(% style="text-align:center" %)QAD|(% style="text-align:center" %)CAD|(% style="text-align:center" %) |(% style="text-align:center" %)✓|100|°/s^^2^^|Increments of 10°/s^^2^^. Only when motion profile is enabled (EM1).
++| |[[**G**yre Direction>>||anchor="GYRE_DIRECTION"]]|(% style="text-align:center" %)G|(% style="text-align:center" %)QG|(% style="text-align:center" %)CG|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|1| |Gyre / rotation direction: 1= CW (clockwise) -1 = CCW (counter-clockwise)
++| |[[**F**irst Position (**D**eg)>>||anchor="FIRST_POSITION"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QFD|(% style="text-align:center" %)CFD|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|No value|1/10°|Reset required after change.
++| |[[**M**aximum **M**otor **D**uty>>||anchor="MAXIMUM_RAW"]]|(% style="text-align:center" %)MMD|(% style="text-align:center" %)QMMD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓|1023|255 to 1023 integer|
++| |[[Maximum **S**peed in **D**egrees>>||anchor="MAXIMUM_SPEED_D"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %)QSD|(% style="text-align:center" %)CSD|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|Max|°/s|SD overwrites SR / CSD overwrites CSR and vice-versa
++| |[[Maximum **S**peed in **R**PM>>||anchor="MAXIMUM_SPEED_RPM"]]|(% style="text-align:center" %)SR|(% style="text-align:center" %)QSR|(% style="text-align:center" %)CSR|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓|Max|RPM|SD overwrites SR / CSD overwrites CSR and vice-versa
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**Modifiers**>>||anchor="HModifiers"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**Modifiers**>>||anchor="MODIFIERS"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Modifier**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[**S**peed>>||anchor="HSpeed28S2CSD29modifier"]]|(% style="text-align:center" %)S|(% style="text-align:center" %)QS|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |uS/s |For P action command
--| |[[**S**peed in **D**egrees>>||anchor="HSpeed28S2CSD29modifier"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |0.1°/s|For D and MD action commands
--| |[[**T**imed move>>||anchor="HTimedmove28T29modifier"]]|(% style="text-align:center" %)T|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |ms|Modifier only for P, D and MD. Time can change based on load
--| |[[**C**urrent **H**old>>||anchor="HCurrentHalt26Hold28CH29modifier"]]|(% style="text-align:center" %)CH|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|Modifier for D, MD, WD and WR
--| |[[**C**urrent **L**imp>>||anchor="HCurrentLimp28CL29modifier"]]|(% style="text-align:center" %)CL|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|Modifier for D, MD, WD and WR
++| |[[**S**peed>>||anchor="SPEEDS"]]|(% style="text-align:center" %)S|(% style="text-align:center" %)QS|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |uS/s |For P action command
++| |[[**S**peed in **D**egrees>>||anchor="SPEEDS"]]|(% style="text-align:center" %)SD|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |°/s|For D and MD action commands
++| |[[**T**imed move>>||anchor="TIMED_MOVE"]]|(% style="text-align:center" %)T|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |ms|Modifier only for P, D and MD. Time can change based on load
++| |[[**C**urrent **H**old>>||anchor="CURRENT_HOLD"]]|(% style="text-align:center" %)CH|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|Modifier for D, MD, WD and WR
++| |[[**C**urrent **L**imp>>||anchor="CURRENT_LIMP"]]|(% style="text-align:center" %)CL|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|Modifier for D, MD, WD and WR
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**Telemetry**>>||anchor="HTelemetry"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**Telemetry**>>||anchor="TELEMETRY"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Action**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[**Q**uery **V**oltage>>||anchor="HQueryVoltage28QV29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QV|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mV|
--| |[[**Q**uery **T**emperature>>||anchor="HQueryTemperature28QT29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°C|
--| |[[**Q**uery **C**urrent>>||anchor="HQueryCurrent28QC29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QC|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|
--| |[[**Q**uery **M**odel **S**tring>>||anchor="HQueryModelString28QMS29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QMS|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Returns the model of servo (ex: LSS-ST1, LSS-HS1, LSS-HT1)
--| |[[**Q**uery **F**irmware Version>>||anchor="HQueryFirmware28QF29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QF|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
--| |[[**Q**uery Serial **N**umber>>||anchor="HQuerySerialNumber28QN29"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QN|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Returns the unique serial number for the servo
++| |[[**Q**uery **V**oltage>>||anchor="QUERY_VOLTAGE"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QV|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mV|
++| |[[**Q**uery **T**emperature>>||anchor="QUERY_TEMP"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QT|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |1/10°C|
++| |[[**Q**uery **C**urrent>>||anchor="QUERY_CURRENT"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QC|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| |mA|
++| |[[**Q**uery **M**odel **S**tring>>||anchor="QUERY_MODEL"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QMS|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Returns the model of servo (ex: LSS-ST1, LSS-HS1, LSS-HT1)
++| |[[**Q**uery **F**irmware Version>>||anchor="QUERY_FIRMWARE"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QF|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |
++| |[[**Q**uery Serial **N**umber>>||anchor="QUERY_SERIAL"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QN|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)✓| | |Returns the unique serial number for the servo
--|(% colspan="10" style="color:orange; font-size:18px" %)[[**RGB LED**>>||anchor="HRGBLED"]]
++|(% colspan="10" style="color:orange; font-size:18px" %)[[**RGB LED**>>||anchor="RGB_LED"]]
  |(% style="width:25px" %) |(% style="width:200px" %)**Description**|(% style="text-align:center; width:100px" %)**Action**|(% style="text-align:center; width:75px" %)**Query**|(% style="text-align:center; width:75px" %)**Config**|(% style="text-align:center; width:75px" %)**RC**|(% style="text-align:center; width:75px" %)**Serial**|(% style="width:100px" %)**Default**|(% style="width:170px" %)**Unit**|**Notes**
--| |[[**LED** Color>>||anchor="HLEDColor28LED29"]]|(% style="text-align:center" %)LED|(% style="text-align:center" %)QLED|(% style="text-align:center" %)CLED|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓| |0 to 7 integer|0=Off; 1=Red; 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White
--| |[[**C**onfigure **L**ED **B**linking>>||anchor="HConfigureLEDBlinking28CLB29"]]|(% style="text-align:center" %) |(% style="text-align:center" %) |(% style="text-align:center" %)CLB|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓| |0 to 63 integer|Reset required after change. See command for details.
++| |[[**LED** Color>>||anchor="LED_COLOR"]]|(% style="text-align:center" %)LED|(% style="text-align:center" %)QLED|(% style="text-align:center" %)CLED|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓| |0 to 7 integer|0=Off; 1=Red; 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White
++| |[[**C**onfigure **L**ED **B**linking>>||anchor="LED_BLINK"]]|(% style="text-align:center" %) |(% style="text-align:center" %)QLB|(% style="text-align:center" %)CLB|(% style="text-align:center" %)✓|(% style="text-align:center" %)✓| |0 to 63 integer|Reset required after change. See command for details.
  = (% style="color:inherit; font-family:inherit" %)Details(%%) =
++{{id name="COMMUNICATION_SETUP"/}}
++
  == (% style="color:inherit; font-family:inherit" %)Communication Setup(%%) ==
++{{id name="RESET"/}}
++
  ====== __Reset__ ======
  {{html wiki="true" clean="false"}}
@@ -228,6
          +228,8 @@
  </div></div>
  {{/html}}
++{{id name="DEFAULT"/}}
++
  ====== __Default & confirm__ ======
  {{html wiki="true" clean="false"}}
@@ -244,6
          +244,8 @@
  </div></div>
  {{/html}}
++{{id name="UPDATE_CONFIRM"/}}
++
  ====== __Update & confirm__ ======
  {{html wiki="true" clean="false"}}
@@ -260,6
          +260,8 @@
  </div></div>
  {{/html}}
++{{id name="CONFIRM"/}}
++
  ====== __Confirm__ ======
  {{html wiki="true" clean="false"}}
@@ -272,6
          +272,8 @@
  </div></div>
  {{/html}}
++{{id name="CHANGE_RC"/}}
++
  ====== __Configure RC Mode (**CRC**)__ ======
  {{html wiki="true" clean="false"}}
@@ -291,6
          +291,8 @@
  </div></div>
  {{/html}}
++{{id name="ID"/}}
++
  ====== __Identification Number (**ID**)__ ======
  {{html wiki="true" clean="false"}}
@@ -311,11
          +311,13 @@
  </div></div>
  {{/html}}
++{{id name="BAUDRATE"/}}
++
  ====== __Baud Rate__ ======
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
--A servo's baud rate cannot be set "on the fly" and must be configured via the CB command described below. The factory default baud rate for all servos is 115200. Since smart servos are intended to be daisy chained, in order to respond to the same serial command, all servos in a project should be set to the same baud rate. Setting different baud rates will have the servos respond differently and may create issues. Available baud rates are: 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115.2 kbps, 230.4 kbps, 250.0 kbps, 460.8 kbps, 500.0 kbps, 750.0 kbps, 921.6 kbps. Servos are shipped with a baud rate set to 115200.<div class="wikimodel-emptyline"></div>
++A servo's baud rate cannot be set "on the fly" and must be configured via the CB command described below. The factory default baud rate for all servos is 115200. Since smart servos are intended to be daisy chained, in order to respond to the same serial command, all servos in a project should be set to the same baud rate. Setting different baud rates will have the servos respond differently and may create issues. Available baud rates are: 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115.2 kbps, 230.4 kbps, 250.0 kbps, 460.8 kbps, 500.0 kbps. Servos are shipped with a baud rate set to 115200.<div class="wikimodel-emptyline"></div>
  Query Baud Rate (**QB**)<div class="wikimodel-emptyline"></div>
@@ -333,28
          +333,12 @@
  </div></div>
  {{/html}}
--====== __Automatic Baud Rate__ ======
++{{id name="MOTION"/}}
--{{html clean="false" wiki="true"}}
--<div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
--This option allows the LSS to listen to it's serial input and select the right baudrate automatically.<div class="wikimodel-emptyline"></div>
--
--Query Automatic Baud Rate (**QABR**)<div class="wikimodel-emptyline"></div>
--
--Ex: #5QABR&lt;cr&gt; might return *5ABR0&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--
--Enable Baud Rate (**ABR**)<div class="wikimodel-emptyline"></div>
--
--Ex: #5QABR1&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--Enable baudrate detection on first byte received after power-up.<div class="wikimodel-emptyline"></div>
--
--Ex: #5QABR2,30&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--Enable baudrate detection on first byte received after power-up. If no data for 30 seconds enable detection again on next byte.<div class="wikimodel-emptyline"></div>
--</div></div>
--{{/html}}
--
  == Motion ==
++{{id name="POSITION_D"/}}
++
  ====== __Position in Degrees (**D**)__ ======
  {{html wiki="true" clean="false"}}
@@ -380,6
          +380,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MOVE_D"/}}
++
  ====== __(Relative) Move in Degrees (**MD**)__ ======
  {{html wiki="true" clean="false"}}
@@ -390,6
          +390,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="WHEEL_D"/}}
++
  ====== __Wheel Mode in Degrees (**WD**)__ ======
  {{html wiki="true" clean="false"}}
@@ -406,6
          +406,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="WHEEL_RPM"/}}
++
  ====== __Wheel Mode in RPM (**WR**)__ ======
  {{html wiki="true" clean="false"}}
@@ -422,6
          +422,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="POSITION_PWM"/}}
++
  ====== __Position in PWM (**P**)__ ======
  {{html wiki="true" clean="false"}}
@@ -439,6
          +439,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MOVE_PWM"/}}
++
  ====== __(Relative) Move in PWM (**M**)__ ======
  {{html wiki="true" clean="false"}}
@@ -449,6
          +449,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MOVE_RAW"/}}
++
  ====== __Raw Duty-cycle Move (**RDM**)__ ======
  {{html wiki="true" clean="false"}}
@@ -467,6
          +467,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="QUERY_STATUS"/}}
++
  ====== __Query Status (**Q**)__ ======
  {{html wiki="true" clean="false"}}
@@ -484,7
          +484,7 @@
  | |ex: *5Q3<cr>|3: Accelerating|Increasing speed from rest (or previous speed) towards travel speed
  | |ex: *5Q4<cr>|4: Traveling|Moving at a stable speed
  | |ex: *5Q5<cr>|5: Decelerating|Decreasing from travel speed towards final position.
--| |ex: *5Q6<cr>|6: Holding|Keeping current position (in EM0 mode, return will nornally be holding)
++| |ex: *5Q6<cr>|6: Holding|Keeping current position
  | |ex: *5Q7<cr>|7: Outside limits|{More details coming soon}
  | |ex: *5Q8<cr>|8: Stuck|Motor cannot perform request movement at current speed setting
  | |ex: *5Q9<cr>|9: Blocked|Similar to stuck, but the motor is at maximum duty and still cannot move (i.e.: stalled)
@@ -506,6
          +506,8 @@
  | |ex: *5Q2<cr>|Input voltage detected is below or above acceptable range|Check the voltage of your batteries or power source
  | |ex: *5Q3<cr>|Temperature limit has been reached|The servo is too hot to continue operating safely.
++{{id name="LIMP"/}}
++
  ====== __Limp (**L**)__ ======
  {{html wiki="true" clean="false"}}
@@ -516,6
          +516,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="HALT_HOLD"/}}
++
  ====== __Halt & Hold (**H**)__ ======
  {{html wiki="true" clean="false"}}
@@ -526,24
          +526,24 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MOTION_SETUP"/}}
++
  == Motion Setup ==
++{{id name="MOTION_PROFILE"/}}
++
  ====== __Enable Motion Profile (**EM**)__ ======
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
--EM1 (Enable Motion Profile #1) is the default mode of the LSS and is an easy way to control the servo's position with a single (serial) position command. This mode uses a trapezoidal motion profile which takes care of acceleration, constant speed travel and deceleration. Once the actual position is within a certain value of the target, it switches to a holding algorithm. The LSS commands for Angular Acceleration and Deceleration (AA/CAA/AD/CAD) Angular Stiffness (AS/CAS) and Angular holding stiffness (AH/CAH) affect this motion profile. Modifiers like SD/S and T can be used in EM1.<div class="wikimodel-emptyline"></div>
--
  Ex: #5EM1&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--This command enables a trapezoidal motion profile for servo #5 <div class="wikimodel-emptyline"></div>
++This command enables a trapezoidal motion profile. By default, the trapezoidal motion profile is enabled. If the motion profile is enabled, angular acceleration (AA) and angular deceleration(AD) will have an effect on the motion. Also, SD/S and T modifiers can be used.<div class="wikimodel-emptyline"></div>
  Ex: #5EM0&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--This command will disable the built-in trapezoidal motion profile. As such, the servo will move at full speed to the target position using the D/MD action commands. Modifiers like SD/S or T cannot be used in EM0 mode. By default the Filter Position Counter, or "FPC" is active in EM0 mode to smooth out its operation. EM0 is suggested for applications where an external controller will be determining all incremental intermediate positions of the servo's motion, effectively replacing a trajectory manager. To prevent having to send position commands continuously to reach the desired position in EM0/FPC active (FPC >= 2), an internal position engine (IPE) repeats the last position command. Note that in EM0 mode, the servo will effectively always be in status: Holding (if using the query status command).
++This command will disable the trapezoidal motion profile. As such, the servo will move at full speed for D/MD action commands. Angular acceleration (AA) and angular deceleration(AD) won't have an effect on motion in this mode and modifiers SD/S or T cannot be used.<div class="wikimodel-emptyline"></div>
--<div class="wikimodel-emptyline"></div>
--
  Query Motion Profile (**QEM**)<div class="wikimodel-emptyline"></div>
  Ex: #5QEM&lt;cr&gt; might return *5QEM1&lt;cr&gt;<div class="wikimodel-emptyline"></div>
@@ -558,12
          +558,12 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="FILTER_POSITION_COUNT"/}}
++
  ====== __Filter Position Count (**FPC**)__ ======
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
--The FPC value relates to the depth of a first order filter (exponential weighted average) over the position change. This has the effect of slowing down both acceleration and deceleration while still allowing the LSS to try to reach the desired position at maximum power at all times. A smaller FPC value will reduce the smoothing effect and a larger value will increase it. To prevent having to send position commands continuously to reach the desired position in EM0/FPC active (FPC >= 2), an internal position engine (IPE) has been put in place, which is also active by default.
--<div class="wikimodel-emptyline"></div>
  Ex: #5FPC10&lt;cr&gt;<div class="wikimodel-emptyline"></div>
  This command allows the user to change the Filter Position Count value for that session. <div class="wikimodel-emptyline"></div>
@@ -581,6
          +581,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ORIGIN_OFFSET"/}}
++
  ====== __Origin Offset (**O**)__ ======
  {{html wiki="true" clean="false"}}
@@ -609,6
          +609,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ANGULAR_RANGE"/}}
++
  ====== __Angular Range (**AR**)__ ======
  {{html wiki="true" clean="false"}}
@@ -637,6
          +637,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ANGULAR_STIFFNESS"/}}
++
  ====== __Angular Stiffness (**AS**)__ ======
  {{html wiki="true" clean="false"}}
@@ -669,6
          +669,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ANGULAR_HOLDING_STIFFNESS"/}}
++
  ====== __Angular Holding Stiffness (**AH**)__ ======
  {{html wiki="true" clean="false"}}
@@ -693,6
          +693,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ANGULAR_ACCELERATION"/}}
++
  ====== __Angular Acceleration (**AA**)__ ======
  {{html wiki="true" clean="false"}}
@@ -717,6
          +717,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="ANGULAR_DECELERATION"/}}
++
  ====== __Angular Deceleration (**AD**)__ ======
  {{html wiki="true" clean="false"}}
@@ -741,6
          +741,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="GYRE_DIRECTION"/}}
++
  ====== __Gyre Direction (**G**)__ ======
  {{html wiki="true" clean="false"}}
@@ -765,6
          +765,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="FIRST_POSITION"/}}
++
  ====== __First Position__ ======
  {{html wiki="true" clean="false"}}
@@ -785,6
          +785,8 @@
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MAXIMUM_RAW"/}}
++
  ====== __Maximum Motor Duty (**MMD**)__ ======
  {{html wiki="true" clean="false"}}
@@ -799,10
          +799,12 @@
  Ex: #5QMMDD&lt;cr&gt; might return *5QMMD512&lt;cr&gt; <div class="wikimodel-emptyline"></div>
--This command returns the configured limit of the duty cycle value sent from the servo's MCU to the Motor Controller. The default value is 1023.
++This configuration command means the servo, when set to smart mode, will immediately move to 90.0 degrees upon power up. Sending a CFD command without a number (Ex. #5CFD&lt;cr&gt;) results in the servo remaining limp upon power up. In order to remove the first position, send no value, ex: #5CFD&lt;cr&gt;
  <div class="wikimodel-emptyline"></div></div></div>
  {{/html}}
++{{id name="MAXIMUM_SPEED_D"/}}
++
  ====== __Maximum Speed in Degrees (**SD**)__ ======
  {{html wiki="true" clean="false"}}
@@ -829,6
          +829,8 @@
  </div></div>
  {{/html}}
++{{id name="MAXIMUM_SPEED_RPM"/}}
++
  ====== __Maximum Speed in RPM (**SR**)__ ======
  {{html wiki="true" clean="false"}}
@@ -855,16
          +855,20 @@
  </div></div>
  {{/html}}
++{{id name="MODIFIERS"/}}
++
  == Modifiers ==
++{{id name="SPEEDS"/}}
++
  ====== __Speed (**S**, **SD**) modifier__ ======
--{{html clean="false" wiki="true"}}
++{{html wiki="true" clean="false"}}
  <div class="cmdcnt"><div class="cmdpad"></div><div class="cmdtxt">
  Example: #5P1500S750&lt;cr&gt;<div class="wikimodel-emptyline"></div>
  Modifier (S) is only for a position (P) action and determines the speed of the move in microseconds per second. A speed of 750 microseconds would cause the servo to rotate from its current position to the desired position at a speed of 750 microseconds per second. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.<div class="wikimodel-emptyline"></div>
  Example: #5D0SD180&lt;cr&gt;<div class="wikimodel-emptyline"></div>
--Modifier (SD) is only for a position (D) or relative position (MD) action and determines the speed of the move in tenths of degrees per second. A speed modifier (SD) of 180 would cause the servo to rotate from its current position to the desired absolute or relative position at a speed of 18 degrees per second.<div class="wikimodel-emptyline"></div>
++Modifier (SD) is only for a position (D) or relative position (MD) action and determines the speed of the move in degrees per second. A speed modifier (SD) of 180 would cause the servo to rotate from its current position to the desired absolute or relative position at a speed of 180 degrees per second.<div class="wikimodel-emptyline"></div>
  Query Speed (**QS**)<div class="wikimodel-emptyline"></div>
  Example: #5QS&lt;cr&gt; might return *5QS300&lt;cr&gt;<div class="wikimodel-emptyline"></div>
  This command queries the current speed in microseconds per second.<div class="wikimodel-emptyline"></div>
@@ -871,6
          +871,8 @@
  </div></div>
  {{/html}}
++{{id name="TIMED_MOVE"/}}
++
  ====== __Timed move (**T**) modifier__ ======
  {{html wiki="true" clean="false"}}
@@ -882,6
          +882,8 @@
  </div></div>
  {{/html}}
++{{id name="CURRENT_HOLD"/}}
++
  ====== __Current Halt & Hold (**CH**) modifier__ ======
  {{html wiki="true" clean="false"}}
@@ -893,6
          +893,8 @@
  </div></div>
  {{/html}}
++{{id name="CURRENT_LIMP"/}}
++
  ====== __Current Limp (**CL**) modifier__ ======
  {{html wiki="true" clean="false"}}
@@ -904,8
          +904,12 @@
  </div></div>
  {{/html}}
++{{id name="TELEMETRY"/}}
++
  == Telemetry ==
++{{id name="QUERY_VOLTAGE"/}}
++
  ====== __Query Voltage (**QV**)__ ======
  {{html wiki="true" clean="false"}}
@@ -915,6
          +915,8 @@
  </div></div>
  {{/html}}
++{{id name="QUERY_TEMP"/}}
++
  ====== __Query Temperature (**QT**)__ ======
  {{html wiki="true" clean="false"}}
@@ -924,6
          +924,8 @@
  </div></div>
  {{/html}}
++{{id name="QUERY_CURRENT"/}}
++
  ====== __Query Current (**QC**)__ ======
  {{html wiki="true" clean="false"}}
@@ -933,6
          +933,8 @@
  </div></div>
  {{/html}}
++{{id name="QUERY_MODEL"/}}
++
  ====== __Query Model String (**QMS**)__ ======
  {{html wiki="true" clean="false"}}
@@ -942,6
          +942,8 @@
  </div></div>
  {{/html}}
++{{id name="QUERY_FIRMWARE"/}}
++
  ====== __Query Firmware (**QF**)__ ======
  {{html wiki="true" clean="false"}}
@@ -952,6
          +952,8 @@
  </div></div>
  {{/html}}
++{{id name="QUERY_SERIAL"/}}
++
  ====== __Query Serial Number (**QN**)__ ======
  {{html wiki="true" clean="false"}}
@@ -961,8
          +961,12 @@
  </div></div>
  {{/html}}
++{{id name="RGB_LED"/}}
++
  == RGB LED ==
++{{id name="LED_COLOR"/}}
++
  ====== __LED Color (**LED**)__ ======
  {{html wiki="true" clean="false"}}
@@ -979,6
          +979,8 @@
  </div></div>
  {{/html}}
++{{id name="LED_BLINK"/}}
++
  ====== __Configure LED Blinking (**CLB**)__ ======
  {{html wiki="true" clean="false"}}

Changes for page LSS Communication Protocol

Summary

Details

Navigation

Recently Visited