Changes for page LSS Communication Protocol

Last modified by Eric Nantel on 2025/06/06 07:47

From version < 23.1 >

edited by RB1
on 2018/05/04 09:28

To version < 39.1 >

edited by Coleman Benson
on 2018/05/24 14:26

< >

Change comment: There is no comment for this version

Summary

Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

@@ -1,1
          +1,1 @@
--xwiki:XWiki.RB1
++xwiki:XWiki.CBenson

Content

@@ -48,7
          +48,7 @@
  == Configuration Commands ==
--Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:Lynxmotion Smart Servos (LSS).LSS - RC PWM.WebHome]].
++Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - RC PWM.WebHome]].
 . Start with a number sign # (U+0023)
 . Servo ID number as an integer
@@ -118,17
          +118,17 @@
  | 6|**O**rigin Offset| O| QO| CO| ✓|  ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
  | 7|**A**ngular **R**ange| AR| QAR| CAR| ✓|  ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
  | 8|Position in **P**ulse| P| QP| | | ✓| microseconds|(((
--See details below.
++See details below
  )))
  | 9|Position in **D**egrees| D| QD| | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
  | 10|**W**heel mode in **D**egrees| WD| QWD| | | ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|
  | 11|**W**heel mode in **R**PM| WR| QWR| | | ✓| rpm|
--| 12|**S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|
--| 13|**S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|
--| 14|**R**igidity| R| QR| CR| ✓| ✓|none|
++| 12|Max **S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|Add modifier "2" for instantaneous speed
++| 13|Max **S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|Add modifier "2" for instantaneous speed
++| 14|**A**ngular **S**tiffness| AS| QAS| CAS| ✓| ✓|none|
  | 15|//N/A (removed)//| | | | | | |
--| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6= 7=MAGENTA, 8=WHITE
--| 17|**ID** #| ID| QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to.
++| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=VIOLET 7=MAGENTA, 8=WHITE
++| 17|**ID** #| ID| QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
  | 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
  | 19|**G**yre direction (**G**)| G| QG| CG| ✓| ✓| none | Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)
  | 20|**F**irst Position (**P**ulse)| | QFP|CFP | ✓| ✓| none |
@@ -137,7
          +137,7 @@
  | 23|**M**odel| | QM| | | | none (integer)|
  | 24|Serial **N**umber| | QN| | | | none (integer)|
  | 25|**F**irmware version| | QF| | | | none (integer)|
--| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)|
++| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)| See command description for details
  | 27|**V**oltage| | QV| | | ✓| tenths of volt (ex 113 = 11.3V; 92 = 9.2V)|
  | 28|**T**emperature| | QT| | | ✓| degrees Celsius|
  | 29|**C**urrent| | QC| | | ✓| tenths of Amps (ex 2 = 0.2A)|
@@ -232,10
          +232,10 @@
  Query Position in Pulse (**QP**)
--Example: #5QP<cr> might return *5QP
++Example: #5QP<cr> might return *5QP2334
  This command queries the current angular position in PWM "units". The user must take into consideration that the response includes any angular range and origin configurations in order to determine the actual angle.
--Valid values for QP are {-500, [500, 2500], -2500}. Values outside the [500, 2500] range are given a negative corresponding end point value to indicate they are out of bounds.
++Valid values for QP are {-500, [500, 2500], -2500}. Values outside the [500, 2500] range are given a negative corresponding end point value to indicate they are out of bounds (note that if the servo is physically located at one of the endpoints, it may return a negative number if it is a fraction of a degree beyond the position).
  __9. Position in Degrees (**D**)__
@@ -247,8
          +247,10 @@
  Query Position in Degrees (**QD**)
--Example: #5QD<cr> might return *5QD0<cr>
++Example: #5QD<cr> might return *5QD132<cr>
++This means the servo is located at 13.2 degrees.
++
  __10. Wheel Mode in Degrees (**WD**)__
  Ex: #5WD900<cr>
@@ -283,13
          +283,14 @@
  Ex: #5QSD<cr> might return *5QSD1800<cr>
--By default QSD will return the current session value, which is set to the value of CSD as reset/power cycle and changed whenever a SD command is processed.
++By default QSD will return the current session value, which is set to the value of CSD as reset/power cycle and changed whenever a SD/SR command is processed.
  If #5QSD1<cr> is sent, the configured maximum speed (CSD value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:
--no param = session max velocity
--1 = configured max velocity
--2 = current velocity
--3 = target/travel velocity (temporary until next motion command)
++|**Command sent**|**Returned value (1/10 °)**
++|ex: #5QSD<cr>|Session value for maximum speed (set by latest SD/SR command)
++|ex: #5QSD1<cr>|Configured maximum speed  (set by CSD/CSR)
++|ex: #5QSD2<cr>|Instantaneous speed (same as QWD)
++|ex: #5QSD3<cr>|Target travel speed
  Configure Speed in Degrees (**CSD**)
@@ -307,19
          +307,26 @@
  Ex: #5QSR<cr> might return *5QSR45<cr>
--Note that the QSD query will return the current servo speed. Querying the last maximum speed value set using SR or CSR is not possible.
++By default QSR will return the current session value, which is set to the value of CSR as reset/power cycle and changed whenever a SD/SR command is processed.
++If #5QSR1<cr> is sent, the configured maximum speed (CSR value) will be returned instead. You can also query the current speed using "2" and the current target travel speed using "3". See the table below for an example:
--Configure Speed in Degrees (**CSR**)
++|**Command sent**|**Returned value (1/10 °)**
++|ex: #5QSR<cr>|Session value for maximum speed (set by latest SD/SR command)
++|ex: #5QSR1<cr>|Configured maximum speed  (set by CSD/CSR)
++|ex: #5QSR2<cr>|Instantaneous speed (same as QWR)
++|ex: #5QSR3<cr>|Target travel speed
++Configure Speed in RPM (**CSR**)
++
  Ex: #5CSR45<cr>
--Using the CSD command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSD value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
++Using the CSR command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSR value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
--__14. Rigidity (R)__
++__14. Angular Stiffness (AS)__
--The servo's rigidity can be thought of as (though not identical to) a damped spring in which the rigidity value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes.
++The servo's rigidity / angular stiffness can be thought of as (though not identical to) a damped spring in which the value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes.
--A positive value of "rigidity":
++A positive value of "angular stiffness":
  * The more torque will be applied to try to keep the desired position against external input / changes
  * The faster the motor will reach its intended travel speed and the motor will decelerate faster and nearer to its target position
@@ -331,17
          +331,17 @@
  The default value is zero and the effect becomes extreme by -4, +4. There are no units, only integers between -4 to 4. Greater values produce increasingly erratic behavior.
--Ex: #5R-2<cr>
++Ex: #5AS-2<cr>
--This reduces the rigidity to -2 for that session, allowing the servo to deviate more around the desired position. This can be beneficial in many situations such as impacts (legged robots) where more of a "spring" effect is desired. Upon reset, the servo will use the value stored in memory, based on the last configuration command.
++This reduces the angular stiffness to -2 for that session, allowing the servo to deviate more around the desired position. This can be beneficial in many situations such as impacts (legged robots) where more of a "spring" effect is desired. Upon reset, the servo will use the value stored in memory, based on the last configuration command.
--Ex: #5QR<cr>
++Ex: #5QAS<cr>
  Queries the value being used.
--Ex: #5CR<cr>
++Ex: #5CAS<cr>
--Writes the desired rigidity value to memory.
++Writes the desired angular stiffness value to memory.
  __15. N/A (removed)__
@@ -363,7
          +363,7 @@
  Configure LED Color (**CLED**)
--Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle.
++Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle. Note that it also changes the session's LED color immediately as well.
  __17. Identification Number__
@@ -371,13
          +371,13 @@
  Query Identification (**QID**)
--EX: #QID<cr> might return *QID5<cr>
++EX: #254QID<cr> might return *QID5<cr>
--When using the query ID command, it is best to only have one servo connected and thus receive only one reply.
++When using the query ID command, it is best to only have one servo connected and thus receive only one reply using the broadcast command (ID 254). Alternatively, pushing the button upon startup and temporarily setting the servo ID to 255 will still result in the servo responding with its "real" ID.
  Configure ID (**CID**)
--Ex: #CID5<cr>
++Ex: #4CID5<cr>
  Setting a servo's ID in EEPROM is done via the CID command. All servos connected to the same serial bus will be assigned that ID. In most situations each servo must be set a unique ID, which means each servo must be connected individually to the serial bus and receive a unique CID number. It is best to do this before the servos are added to an assembly. Numbered stickers are provided to distinguish each servo after their ID is set, though you are free to use whatever alternative method you like.
@@ -424,13
          +424,13 @@
  Ex: #5QFP<cr> might return *5QFP1550<cr>
--The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds.
++The reply above indicates that servo with ID 5 has a first position pulse of 1550 microseconds. If no first position has been set, servo will respond with DIS ("disabled").
--Configure First Position in Pulses (CFP)
++Configure First Position in Pulses (**CFP**)
  Ex: #5CP1550<cr>
--This configuration command means the servo, when set to RC mode, will immediately move to an angle equivalent to having received an RC pulse of 1550 microseconds upon power up. Sending a CFP command without a number results in the servo remaining limp upon power up.
++This configuration command means the servo, when set to RC mode, will immediately move to an angle equivalent to having received an RC pulse of 1550 microseconds upon power up. Sending a CFP command without a number results in the servo remaining limp upon power up (i.e. disabled).
  __21. First / Initial Position (Degrees)__
@@ -474,9
          +474,20 @@
  __26. Query Status (**Q**)__
--Ex: #5Q<cr> might return *5Q_<cr>
++Ex: #5Q<cr> might return *5Q6<cr>, which indicates the motor is holding a position.
--{Description coming soon}
++|*Value returned|**Status**|**Detailed description**
++|ex: *5Q0<cr>|Unknown|LSS is unsure
++|ex: *5Q1<cr>|Limp|Motor driving circuit is not powered and horn can be moved freely
++|ex: *5Q2<cr>|Free moving|Motor driving circuit is not powered and horn can be moved freely
++|ex: *5Q3<cr>|Accelerating|Increasing speed from rest (or previous speeD) towards travel speed
++|ex: *5Q4<cr>|Traveling|Moving at a stable speed
++|ex: *5Q5<cr>|Deccelerating|Decreasing speed towards travel speed towards rest
++|ex: *5Q6<cr>|Holding|Keeping current position
++|ex: *5Q7<cr>|Stepping|Special low speed mode to maintain torque
++|ex: *5Q8<cr>|Outside limits|More details coming soon
++|ex: *5Q9<cr>|Stuck|Motor cannot perform request movement at current speed setting
++|ex: *5Q10<cr>|Blocked|Similar to stuck, but the motor is at maxiumum duty and still cannot move (i.e.: stalled)
  __27. Query Voltage (**QV**)__

Changes for page LSS Communication Protocol

Summary

Details

Navigation

Recently Visited