Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Parent

...	...	@@ -1,1 +1,1 @@
1		-Main.WebHome
	1	+lynxmotion:LSS - Overview (DEV).WebHome

Content

...	...	@@ -48,7 +48,7 @@
48	48
49	49	== Configuration Commands ==
50	50
51		-Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - RC PWM.WebHome]].
	51	+Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - Overview (DEV).LSS - RC PWM.WebHome]].
52	52
53	53	1. Start with a number sign # (U+0023)
54	54	1. Servo ID number as an integer
...	...	@@ -127,7 +127,7 @@
127	127	| 13|Max **S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|Add modifier "2" for instantaneous speed
128	128	| 14|**A**ngular **S**tiffness| AS| QAS| CAS| ✓| ✓|none|
129	129	| 15|//N/A (removed)//| | | | | | |
130		-| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6= 7=MAGENTA, 8=WHITE
	130	+| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=VIOLET 7=MAGENTA, 8=WHITE
131	131	| 17|**ID** #| ID| QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
132	132	| 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
133	133	| 19|**G**yre direction (**G**)| G| QG| CG| ✓| ✓| none | Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)
...	...	@@ -139,10 +139,10 @@
139	139	| 25|**F**irmware version| | QF| | | | none (integer)|
140	140	| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)| See command description for details
141	141	| 27|**V**oltage| | QV| | | ✓| tenths of volt (ex 113 = 11.3V; 92 = 9.2V)|
142		-| 28|**T**emperature| | QT| | | ✓| degrees Celsius|
	142	+| 28|**T**emperature| | QT| | | ✓| degrees Celsius|Max temp before error: 85°C (servo goes limp)
143	143	| 29|**C**urrent| | QC| | | ✓| tenths of Amps (ex 2 = 0.2A)|
	144	+|30|**RC** Mode| | |CRC| |✓| |Puts the servo into RC mode. To revert to serial mode, use the button menu.
144	144	| | | | | | | | |
145		-| | | | | | | | |
146	146
147	147	= Details =
148	148
...	...	@@ -381,13 +381,13 @@
381	381
382	382	Query Identification (**QID**)
383	383
384		-EX: #QID<cr> might return *QID5<cr>
	384	+EX: #254QID<cr> might return *QID5<cr>
385	385
386		-When using the query ID command, it is best to only have one servo connected and thus receive only one reply.
	386	+When using the query ID command, it is best to only have one servo connected and thus receive only one reply using the broadcast command (ID 254). Alternatively, pushing the button upon startup and temporarily setting the servo ID to 255 will still result in the servo responding with its "real" ID.
387	387
388	388	Configure ID (**CID**)
389	389
390		-Ex: #CID5<cr>
	390	+Ex: #4CID5<cr>
391	391
392	392	Setting a servo's ID in EEPROM is done via the CID command. All servos connected to the same serial bus will be assigned that ID. In most situations each servo must be set a unique ID, which means each servo must be connected individually to the serial bus and receive a unique CID number. It is best to do this before the servos are added to an assembly. Numbered stickers are provided to distinguish each servo after their ID is set, though you are free to use whatever alternative method you like.
393	393
...	...	@@ -511,12 +511,18 @@
511	511
512	512	The units are in tenths of degrees Celcius, so in the example above, the servo's internal temperature is 56.4 degrees C. To convert from degrees Celcius to degrees Farenheit, multiply by 1.8 and add 32. Therefore 56.4C = 133.52F.
513	513
514		-__29. Query Current (QC)__
	514	+__29. Query Current (**QC**)__
515	515
516	516	Ex: #5QC<cr> might return *5QC140<cr>
517	517
518	518	The units are in milliamps, so in the example above, the servo is consuming 140mA, or 0.14A.
519	519
	520	+__20. RC Mode (**CRC**)__
	521	+
	522	+This command puts the servo into RC mode, where it will only respond to RC pulses. Note that because this is the case, the servo will no longer accept serial commands. The servo can be placed back into serial model only using the button menu.
	523	+
	524	+EX: #5CRC<cr>
	525	+
520	520	__**RESET**__
521	521
522	522	Ex: #5RESET<cr> or #5RS<cr>