Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.CBenson
	1	+xwiki:XWiki.RB1

Content

...	...	@@ -42,10 +42,6 @@
42	42	Action modifiers can only be used with certain commands.
43	43	)))
44	44
45		-(((
46		-
47		-)))
48		-
49	49	== Configuration Commands ==
50	50
51	51	Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - Overview (DEV).LSS - RC PWM.WebHome]].
...	...	@@ -150,7 +150,10 @@
150	150	| 12|Max **S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|QSD: Add modifier "2" for instantaneous speed
151	151	| 13|Max **S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|QSR: Add modifier "2" for instantaneous speed
152	152	| 14|**A**ngular **S**tiffness| AS| QAS| CAS| ✓| ✓|none|-4 to +4, but suggested values are between 0 to +4
153		-| 15|**A**ngular **H**olding Stiffness|AH|QAH|CAH| |✓|none|-10 to +10, with default as 0.
	149	+| 15|**A**ngular **H**olding Stiffness|AH|QAH|CAH| | ✓|none|-10 to +10, with default as 0.
	150	+|15b|**A**ngular **A**cceleration|AA|QAA|CAA| | ✓|degrees per second squared|Increments of 10 degrees per second squared
	151	+|15c|**A**ngular **D**eceleration|AD|QAD|CAD| | ✓|degrees per second squared|Increments of 10 degrees per second squared
	152	+|15d|**M**otion **C**ontrol|MC|QMC| | | ✓|none|MC0 to disable motion control, MC1 to enable. Session specific
154	154	| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=MAGENTA, 7=WHITE
155	155	| 17|**ID** #| | QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
156	156	| 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
...	...	@@ -158,7 +158,8 @@
158	158	| 20|**F**irst Position (**P**ulse)| | QFP|CFP | ✓| ✓| none |
159	159	| 21|**F**irst Position (**D**egrees)| | QFD|CFD| ✓| ✓| none |
160	160	| 22|**T**arget (**D**egree) **P**osition| | QDT| | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
161		-| 23|**M**odel| | QM| | | | none (integer)|
	160	+| 23|**M**odel **String**| | QMS| | | | none (string)| Recommended to determine the model|
	161	+| 23b|**M**odel| | QM| | | | none (integer)| Returns a raw value representing the three model inputs (36 bit)|
162	162	| 24|Serial **N**umber| | QN| | | | none (integer)|
163	163	| 25|**F**irmware version| | QF| | | | none (integer)|
164	164	| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)| See command description for details
...	...	@@ -398,12 +398,24 @@
398	398
399	399	This returns the servo's angular holding stiffness value.
400	400
401		-Configure Angular Hold Stiffness (CAH)
	401	+Configure Angular Hold Stiffness (**CAH**)
402	402
403	403	Ex: #5CAH2<cr>
404	404
405	405	This writes the angular holding stiffness of servo #5 to 2 to EEPROM
406	406
	407	+__15b: Angular Acceleration (**AA**)__
	408	+
	409	+{More details to come}
	410	+
	411	+__15c: Angular Deceleration (**AD**)__
	412	+
	413	+{More details to come}
	414	+
	415	+__15d: Motion Control (**MC**)__
	416	+
	417	+{More details to come}
	418	+
407	407	__16. RGB LED (**LED**)__
408	408
409	409	Ex: #5LED3<cr>
...	...	@@ -511,12 +511,18 @@
511	511
512	512	The query target position command returns the target angle during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond without a number (Ex: *5QDT<cr>).
513	513
514		-__23. Query Model (**QM**)__
	526	+__23. Query Model String (**QMS**)__
515	515
516		-Ex: #5QM<cr> might return *5QM11<cr>
	528	+Ex: #5QMS<cr> might return *5QMSLSS-HS1cr>
517	517
518		-This reply means the servo model is 1.1, meaning high speed servo, first revision. 1=HS (high speed) 2=ST (standard) 3=HT (high torque)
	530	+This reply means the servo model is LSS-HS1, meaning a high speed servo, first revision.
519	519
	532	+__23b. Query Model (**QM**)__
	533	+
	534	+Ex: #5QM<cr> might return *5QM68702699520cr>
	535	+
	536	+This reply means the servo model is 0xFFF000000 or 100, meaning a high speed servo, first revision.
	537	+
520	520	__24. Query Serial Number (**QN**)__
521	521
522	522	Ex: #5QN<cr> might return *5QN~_~_<cr>