Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -42,6 +42,10 @@
42	42	Action modifiers can only be used with certain commands.
43	43	)))
44	44
	45	+(((
	46	+
	47	+)))
	48	+
45	45	== Configuration Commands ==
46	46
47	47	Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - Overview (DEV).LSS - RC PWM.WebHome]].
...	...	@@ -146,10 +146,7 @@
146	146	| 12|Max **S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|QSD: Add modifier "2" for instantaneous speed
147	147	| 13|Max **S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|QSR: Add modifier "2" for instantaneous speed
148	148	| 14|**A**ngular **S**tiffness| AS| QAS| CAS| ✓| ✓|none|-4 to +4, but suggested values are between 0 to +4
149		-| 15|**A**ngular **H**olding Stiffness|AH|QAH|CAH| | ✓|none|-10 to +10, with default as 0.
150		-|15b|**A**ngular **A**cceleration|AA|QAA|CAA| | ✓|degrees per second squared|Increments of 10 degrees per second squared
151		-|15c|**A**ngular **D**eceleration|AD|QAD|CAD| | ✓|degrees per second squared|Increments of 10 degrees per second squared
152		-|15d|**M**otion **C**ontrol|MC|QMC| | | ✓|none|MC0 to disable motion control, MC1 to enable. Session specific
	153	+| 15|**A**ngular **H**olding Stiffness|AH|QAH|CAH| |✓|none|-10 to +10, with default as 0.
153	153	| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=MAGENTA, 7=WHITE
154	154	| 17|**ID** #| | QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
155	155	| 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
...	...	@@ -397,24 +397,12 @@
397	397
398	398	This returns the servo's angular holding stiffness value.
399	399
400		-Configure Angular Hold Stiffness (**CAH**)
	401	+Configure Angular Hold Stiffness (CAH)
401	401
402	402	Ex: #5CAH2<cr>
403	403
404	404	This writes the angular holding stiffness of servo #5 to 2 to EEPROM
405	405
406		-__15b: Angular Acceleration (**AA**)__
407		-
408		-{More details to come}
409		-
410		-__15c: Angular Deceleration (**AD**)__
411		-
412		-{More details to come}
413		-
414		-__15d: Motion Control (**MC**)__
415		-
416		-{More details to come}
417		-
418	418	__16. RGB LED (**LED**)__
419	419
420	420	Ex: #5LED3<cr>