Summary

• Page properties (2 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.RB1
	1	+xwiki:XWiki.CBenson

Content

...	...	@@ -1,10 +5,6 @@
1		-{{toc depth="3"/}}
2		-
3		-= Protocol concepts =
4		-
5	5	The Lynxmotion Smart Servo (LSS) protocol was created in order to be as simple and straightforward as possible from a user perspective, while at the same time trying to stay compact and robust yet highly versatile. Almost everything one might expect to be able to configure for a smart servo motor is available.
6	6
7		-== Session ==
	3	+=== Session ===
8	8
9	9	A "session" is defined as the time between when the servo is powered ON to when it is powered OFF or reset.
10	10
...	...	@@ -161,8 +161,7 @@
161	161	| 20|**F**irst Position (**P**ulse)| | QFP|CFP | ✓| ✓| none |
162	162	| 21|**F**irst Position (**D**egrees)| | QFD|CFD| ✓| ✓| none |
163	163	| 22|**T**arget (**D**egree) **P**osition| | QDT| | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
164		-| 23|**M**odel **String**| | QMS| | | | none (string)| Recommended to determine the model|
165		-| 23b|**M**odel| | QM| | | | none (integer)| Returns a raw value representing the three model inputs (36 bit)|
	160	+| 23|**M**odel| | QM| | | | none (integer)|
166	166	| 24|Serial **N**umber| | QN| | | | none (integer)|
167	167	| 25|**F**irmware version| | QF| | | | none (integer)|
168	168	| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)| See command description for details
...	...	@@ -179,9 +179,9 @@
179	179	|32|**DEFAULT**| | | | |✓|none|Revert to firmware default values. See command for details
180	180	|33|**UPDATE**| | | | |✓|none|Update firmware. See command for details.
181	181
182		-== Details ==
	177	+= Details =
183	183
184		-==== __1. Limp (**L**)__ ====
	179	+__1. Limp (**L**)__
185	185
186	186	Example: #5L<cr>
187	187
...	...	@@ -527,18 +527,12 @@
527	527
528	528	The query target position command returns the target angle during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond without a number (Ex: *5QDT<cr>).
529	529
530		-__23. Query Model String (**QMS**)__
	525	+__23. Query Model (**QM**)__
531	531
532		-Ex: #5QMS<cr> might return *5QMSLSS-HS1cr>
	527	+Ex: #5QM<cr> might return *5QM11<cr>
533	533
534		-This reply means the servo model is LSS-HS1, meaning a high speed servo, first revision.
	529	+This reply means the servo model is 1.1, meaning high speed servo, first revision. 1=HS (high speed) 2=ST (standard) 3=HT (high torque)
535	535
536		-__23b. Query Model (**QM**)__
537		-
538		-Ex: #5QM<cr> might return *5QM68702699520cr>
539		-
540		-This reply means the servo model is 0xFFF000000 or 100, meaning a high speed servo, first revision.
541		-
542	542	__24. Query Serial Number (**QN**)__
543	543
544	544	Ex: #5QN<cr> might return *5QN~_~_<cr>
...	...	@@ -627,3 +627,5 @@
627	627	Since it it not common to have to update firmware, a confirmation command is needed after an UPDATE command is sent. Should any command other than CONFIRM be received by the servo after the firmware command has been received, it will leave the firmware action.
628	628
629	629	Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
	619	+
	620	+=== ===