Summary

• Page properties (3 modified, 0 added, 0 removed)

Details

Page properties

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.ENantel
	1	+xwiki:XWiki.RB1

Tags

...	...	@@ -1,1 +1,1 @@
1		-LSS|communication|protocol|programming|firmware|control
	1	+LSS|communication|protocol|programming|firmware|control|LSS-Ref

Content

...	...	@@ -1,4 +1,5 @@
1		-= Table of Contents =
	1	+(% class="wikigeneratedid" id="HTableofContents" %)
	2	+**Table of Contents**
2	2
3	3	{{toc depth="3"/}}
4	4
...	...	@@ -156,7 +156,8 @@
156	156	|15b|[[**A**ngular **A**cceleration>>||anchor="H15b:AngularAcceleration28AA29"]]|AA|QAA|CAA| | ✓|degrees per second squared|Increments of 10 degrees per second squared
157	157	|15c|[[**A**ngular **D**eceleration>>||anchor="H15c:AngularDeceleration28AD29"]]|AD|QAD|CAD| | ✓|degrees per second squared|Increments of 10 degrees per second squared
158	158	|15d|[[**E**nable **M**otion control>>||anchor="H15d:MotionControl28MC29"]]|EM|QEM| | | ✓|none|EM0 to disable motion control, EM1 to enable. Session specific / does not survive power cycles
159		-| 16|[[**LED** Color>>||anchor="H16.RGBLED28LED29"]]| LED| QLED| CLED| ✓| ✓|none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=MAGENTA, 7=WHITE
	160	+| 16|[[**LED** Color>>||anchor="H16.RGBLED28LED29"]]| LED| QLED| CLED| ✓| ✓|none (integer from 0 to 8)|0=Off (black); 1=Red 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White;
	161	+| 16b|[[**L**ED Blinking>>||anchor="H16b.LEDBlinking"]]| | | CLB| ✓| |none (integer from 0 to 63)|0=No blinking, Blink while: 1=Limp; 2=Holding 3=Accel; 4=Decel; 5=Free 6=Travel; 63=Always blink;
160	160	| 17|[[**ID** #>>||anchor="H17.IdentificationNumber"]]| | QID| CID| | ✓|none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
161	161	| 18|[[**B**aud rate>>||anchor="H18.BaudRate"]]| B| QB| CB| | ✓|none (integer)|
162	162	| 19|[[**G**yre direction (**G**)>>||anchor="H19.GyreRotationDirection"]]| G| QG| CG| ✓| ✓|none | Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)
...	...	@@ -442,6 +442,10 @@
442	442
443	443	Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle. Note that it also changes the session's LED color immediately as well.
444	444
	447	+====== __16b. Configure LED Blinking (**CLB**)__ ======
	448	+
	449	+???
	450	+
445	445	====== __17. Identification Number__ ======
446	446
447	447	A servo's identification number cannot be set "on the fly" and must be configured via the CID command described below. The factory default ID number for all servos is 0. Since smart servos are intended to be daisy chained, in order to respond differently from one another, the user must set different identification numbers. Servos with the same ID and baud rate will all receive and react to the same commands.