Summary

• Page properties (4 modified, 0 added, 0 removed)
• Objects (0 modified, 0 added, 3 removed)
  • XWiki.XWikiRights[0]
  • XWiki.XWikiRights[1]
  • XWiki.XWikiRights[2]

Details

Page properties

Parent

...	...	@@ -1,1 +1,1 @@
1		-Lynxmotion Smart Servo (LSS).WebHome
	1	+lynxmotion:LSS - Overview (DEV).WebHome

Author

...	...	@@ -1,1 +1,1 @@
1		-xwiki:XWiki.CBenson
	1	+xwiki:XWiki.RB1

Tags

...	...	@@ -1,1 +1,1 @@
1		-LSS|communication|protocol|programming|firmware|control|LSS-Ref
	1	+LSS|communication|protocol|programming|firmware|control

Content

...	...	@@ -1,23 +4,16 @@
1		-(% class="wikigeneratedid" id="HTableofContents" %)
2		-**Table of Contents**
3		-
4	4	{{toc depth="3"/}}
5	5
6		-= Serial Protocol Concept =
	3	+= Protocol concepts =
7	7
8		-The custom Lynxmotion Smart Servo (LSS) serial protocol was created in order to be as simple and straightforward as possible from a user perspective ("human readable format"), while at the same time compact and robust yet highly versatile. The protocol was based on Lynxmotion's SSC-32 RC servo controller and almost everything one might expect to be able to configure for a smart servo motor is available.
	5	+The Lynxmotion Smart Servo (LSS) protocol was created in order to be as simple and straightforward as possible from a user perspective, while at the same time trying to stay compact and robust yet highly versatile. Almost everything one might expect to be able to configure for a smart servo motor is available.
9	9
10		-In order to have servos react differently when commands are sent to all servos in a serial bus, the first step a user should take is to assign a different ID number to each servo (explained below). Once this has been done, only the servo(s) which have been assigned to the ID sent as part of the command will follow that command. There is currently no CRC / checksum implemented as part of the protocol.
11		-
12	12	== Session ==
13	13
14	14	A "session" is defined as the time between when the servo is powered ON to when it is powered OFF or reset.
15	15
16		-Note that for a given session, the action related to a specific commands overrides the stored value in EEPROM.
17		-
18	18	== Action Commands ==
19	19
20		-Action commands tell the servo, within that session, to do something (i.e. "take an action"). The types of action commands which can be sent are described below, and they cannot be combined with other commands such as queries or configurations. Only one action command can be sent at a time. Action commands are session-specific, therefore once a servo is power cycled, it will not have any "memory" of previous actions or virtual positions (described below on this page). Action commands are sent serially to the servo's Rx pin and must be sent in the following format:
	13	+Action commands are sent serially to the servo's Rx pin and must be set in the following format:
21	21
22	22	1. Start with a number sign # (U+0023)
23	23	1. Servo ID number as an integer
...	...	@@ -28,12 +28,16 @@
28	28	(((
29	29	Ex: #5PD1443<cr>
30	30
31		-This sends a serial command to all servo's Rx pins which are connected to the bus and only servo(s) with ID #5 will move to a position in tenths of degrees ("PD") of 144.3 degrees. Any servo on the bus which does not have ID 5 will take no action when receiving this command.
	24	+Move servo with ID #5 to a position of 144.3 degrees.
32	32
33		-== Action Modifiers ==
	26	+Action commands cannot be combined with query commands, and only one action command can be sent at a time.
34	34
35		-Only two commands can be used as action modifiers: Timed Move (T) and Speed (S) described below. Action modifiers can only be used with certain action commands. The format to include a modifier is:
	28	+Action commands are session-specific, therefore once a servo is power cycled, it will not have any "memory" of previous actions or virtual positions (as described at the bottom of this page).
36	36
	30	+=== Action Modifiers ===
	31	+
	32	+Two commands can be used as action modifiers only: Timed Move and Speed. The format is:
	33	+
37	37	1. Start with a number sign # (U+0023)
38	38	1. Servo ID number as an integer
39	39	1. Action command (one to three letters, no spaces, capital or lower case)
...	...	@@ -44,12 +44,32 @@
44	44
45	45	Ex: #5P1456T1263<cr>
46	46
47		-This results in the servo with ID #5 rotating from the current angular position to a pulse position ("P") of 1456 in a time ("T") of 1263 milliseconds.
	44	+Results in the servo rotating from the current angular position to a pulse position of 1456 in 1263 milliseconds.
	45	+
	46	+Action modifiers can only be used with certain commands.
48	48	)))
49	49
	49	+== Configuration Commands ==
	50	+
	51	+Configuration commands affect the servo's current session* but unlike action commands, configuration commands are written to EEPROM and are retained even if the servo loses power (therefore NOT session specific). Not all action commands have a corresponding configuration and vice versa. Certain configurations are retained for when the servo is used in RC model. More information can be found on the [[LSS - RC PWM page>>doc:LSS - Overview (DEV).LSS - RC PWM.WebHome]].
	52	+
	53	+1. Start with a number sign # (U+0023)
	54	+1. Servo ID number as an integer
	55	+1. Configuration command (two to three letters, no spaces, capital or lower case)
	56	+1. Configuration value in the correct units with no decimal
	57	+1. End with a control / carriage return '<cr>'
	58	+
	59	+Ex: #5CO-50<cr>
	60	+
	61	+Assigns an absolute origin offset of -5.0 degrees (with respect to factory origin) to servo #5 and changes the offset for that session to -5.0 degrees.
	62	+
	63	+Configuration commands are not cumulative, in that if two configurations are sent at any time, only the last configuration is used and stored.
	64	+
	65	+*Important Note: the one exception is the baud rate - the servo's current session retains the given baud rate. The new baud rate will only be in place when the servo is power cycled.
	66	+
50	50	== Query Commands ==
51	51
52		-Query commands request information from the servo. They are received via the Rx pin of the servo, and the servo's reply is sent via the servo's Tx pin. Using separate lines for Tx and Rx is called "full duplex". Query commands are also similar to action and configuration commands and must use the following format:
	69	+Query commands are sent serially to the servo's Rx pin and must be set in the following format:
53	53
54	54	1. Start with a number sign # (U+0023)
55	55	1. Servo ID number as an integer
...	...	@@ -61,61 +61,49 @@
61	61	)))
62	62
63	63	(((
64		-The query will return a serial string (almost instantaneously) via the servo's Tx pin with the following format:
	81	+The query will return a value via the Tx pin with the following format:
65	65
66		-1. Start with an asterisk * (U+002A)
	83	+1. Start with an asterisk (U+002A)
67	67	1. Servo ID number as an integer
68	68	1. Query command (one to three letters, no spaces, capital letters)
69	69	1. The reported value in the units described, no decimals.
70	70	1. End with a control / carriage return '<cr>'
71	71
72		-There is currently no option to control how fast a servo replies after it has received a query command, therefore when sending a query command to the bus, the controller should be prepared to immediately "listen" for and parse the reply. Sending multiple queries on a bus in fast succession may result in replies overlapping and giving incorrect or corrupt data. As such, the controller should receive a reply before sending a new command. A reply to the query sent above might be:
73		-
74	74	(((
75	75	Ex: *5QD1443<cr>
76	76	)))
77	77
78		-This indicates that servo #5 is currently at 144.3 degrees (1443 tenths of degrees).
	93	+Indicates that servo #5 is currently at 144.3 degrees.
79	79
80		-== Configuration Commands ==
81		-
82		-Configuration commands and corresponding values affect a servo's defaults which are written to and read from the servo's EEPROM. These configurations are retained in memory after the servo is reset or power is cut / lost. Some configuration commands affect the session, while others do not (see each command for details). Not all action commands have a corresponding configuration and vice versa. More information about which configuration commands are retained when in RC mode can be found on the [[LSS - RC PWM page>>doc:Lynxmotion Smart Servo (LSS).LSS - RC PWM.WebHome]]. Configuration commands are not cumulative, in that if two configurations are sent, one after the next, only the last configuration is used and stored. The format to send a configuration command is identical to that of an action command:
83		-
84		-1. Start with a number sign # (U+0023)
85		-1. Servo ID number as an integer
86		-1. Configuration command (two to three letters, no spaces, capital or lower case)
87		-1. Configuration value in the correct units with no decimal
88		-1. End with a control / carriage return '<cr>'
89		-
90		-Ex: #5CO-50<cr>
91		-
92		-This configures an absolute origin offset ("CO") with respect to factory origin to servo with ID #5 and changes the offset for that session to -5.0 degrees (50 tenths of degrees). Once the servo is powered off and then powered on, zeroing the servo will cause it to move to -5.0 degrees with respect to the factory origin and report its position as 0 degrees. Configuration commands can be undone / reset either by sending the servo's default value for that configuration, or by doing a factory reset (clears all configurations) described below.
93		-
94	94	**Session vs Configuration Query**
95	95
96		-By default, the query command returns the sessions' value. Should no action commands have been sent to change the session value, it will return the value saved in EEPROM which will either be the servo's default, or modified with a configuration command. In order to query the value stored in EEPROM (configuration), add a '1' to the query command:
	97	+By default, the query command returns the sessions' value; should no action commands have been sent to change, it will return the value saved in EEPROM from the last configuration command.
97	97
98		-Ex: #5CSR20<cr> immediately sets the maximum speed for servo #5 to 20rpm (explained below) and changes the value in memory.
	99	+In order to query the value in EEPROM, add a '1' to the query command.
99	99
100		-After RESET, a command of #5SR4<cr> sets the session's speed to 4rpm, but does not change the configuration value in memory. Therefore:
	101	+Ex: #5CSR20<cr> sets the maximum speed for servo #5 to 20rpm upon RESET (explained below).
101	101
102		-#5QSR<cr> would return *5QSR4<cr> which represents the value for that session, whereas
	103	+After RESET: #5SR4<cr> sets the session's speed to 4rpm.
103	103
	105	+#5QSR<cr> would return *5QSR4<cr> which represents the value for that session.
	106	+
104	104	#5QSR1<cr> would return *5QSR20<cr> which represents the value in EEPROM
105	105
106		-== Virtual Angular Position ==
	109	+=== Virtual Angular Position ===
107	107
108		-The ability to store a "virtual angular position" is a feature which allows for rotation beyond 360 degrees, permitting multiple rotations of the output horn, moving the center position and more. In virtual position mode, the "absolute position" would be the angle of the output shaft with respect to a 360.0 degree circle, and can be obtained by taking the modulus (with respect to 360 degrees) of the value. For example if the virtual position is reported as 15335 (or 1533.5 degrees), taking the modulus would give 93.5 degrees (3600 * 4 + 935 = 15335) as the absolute position (assuming no origin offset).
	111	+{In progress}
109	109
	113	+A "virtual position" is one which allows for multiple rotations of the output horn, moving the center position and more. The "absolute position" would be the angle of the output shaft with respect to 360.0 degrees.
	114	+
110	110	[[image:LSS-servo-positions.jpg]]
111	111
112		-In this example, the gyre direction (explained below, a.k.a. "rotation direction") is positive (clockwise), and origin offset has not been modified. Each square represents 30 degrees. The following command is sent:
	117	+Example: Gyre direction / rotation is positive (clockwise), and origin offset has not been modified. Each square represents 30 degrees.
113	113
114		-#1D-300<cr> This causes the servo to move to -30.0 degrees (green arrow)
	119	+#1D-300<cr> The servo is sent a command to move to -30.0 degrees (green arrow)
115	115
116	116	#1D2100<cr> This second position command is sent to the servo, which moves it to 210.0 degrees (orange arrow)
117	117
118		-#1D-4200<cr> This next command rotates the servo counterclockwise to a position of -420 degrees (red arrow), which means one full rotation of 360 degrees plus 60.0 degrees (420.0 - 360.0), with a virtual position of -420.0 degrees.
	123	+#1D-4200<cr> This next command rotates the servo counterclockwise to a position of -420 degrees (red arrow), which means one full rotation of 360 degrees,  stopping at an absolute position of 60.0 degrees (420.0-360.0), with a virtual position of -420.0 degrees.
119	119
120	120	Although the final physical position would be the same as if the servo were commanded to move to -60.0 degrees, the servo is in fact at -420.0 degrees.
121	121
...	...	@@ -128,115 +128,93 @@
128	128
129	129	= Command List =
130	130
131		-|= #|=Description|= Action|= Query|= Config|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
132		-| 1|[[**L**imp>>||anchor="H1.Limp28L29"]]| L| | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
133		-| 2|[[**H**alt & **H**old>>||anchor="H2.Halt26Hold28H29"]]| H| | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
134		-| 3|[[**T**imed move>>||anchor="H3.Timedmove28T29"]]| T| | | | ✓|milliseconds|(% style="width:510px" %) Modifier only for {P, D, MD}|(% style="text-align:center; width:113px" %)
135		-| 4|[[**S**peed>>||anchor="H4.Speed28S29"]]| S| | | | ✓|microseconds per second|(% style="width:510px" %) Modifier only {P}|(% style="text-align:center; width:113px" %)
136		-| 5|[[**M**ove in **D**egrees (relative)>>||anchor="H5.28Relative29MoveinDegrees28MD29"]]| MD| | | | ✓|tenths of degrees (ex 325 = 32.5 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
137		-| 6|[[**O**rigin Offset>>||anchor="H6.OriginOffsetAction28O29"]]| O| QO| __CO__| ✓| ✓|tenths of degrees (ex 91 = 9.1 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
138		-0
	136	+|= #|=Description|= Action|= Query|= Config|= RC|= Serial|= Units|= Notes
	137	+| 1|**L**imp| L| | | | ✓| none|
	138	+| 2|**H**alt & Hold| H| | | | ✓| none|
	139	+| 3|**T**imed move| T| | | | ✓| milliseconds| Modifier only
	140	+| 4|**S**peed| S| | | | ✓| microseconds / second| Modifier only
	141	+| 5|**M**ove in **D**egrees (relative)| MD| | | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
	142	+| 6|**O**rigin Offset| O| QO| CO| ✓| ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
	143	+| 7|**A**ngular **R**ange| AR| QAR| CAR| ✓| ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
	144	+| 8|Position in **P**ulse| P| QP| | | ✓| microseconds|(((
	145	+See details below
139	139	)))
140		-| 7|[[**A**ngular **R**ange>>||anchor="H7.AngularRange28AR29"]]| AR| QAR| CAR| ✓| ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)(((
141		-1800
	147	+| 9|Position in **D**egrees| D| QD| | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
	148	+| 10|**W**heel mode in **D**egrees| WD| QWD| | | ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|
	149	+| 11|**W**heel mode in **R**PM| WR| QWR| | | ✓| rpm|
	150	+| 12|Max **S**peed in **D**egrees| SD| QSD| CSD| ✓| ✓| tenths of degrees per second (ex 248 = 24.8 degrees per second)|QSD: Add modifier "2" for instantaneous speed
	151	+| 13|Max **S**peed in **R**PM| SR| QSR| CSR| ✓| ✓| rpm|QSR: Add modifier "2" for instantaneous speed
	152	+| 14|**A**ngular **S**tiffness| AS| QAS| CAS| ✓| ✓|none|-4 to +4, but suggested values are between 0 to +4
	153	+| 15|**A**ngular **H**olding Stiffness|AH|QAH|CAH| | ✓|none|-10 to +10, with default as 0.
	154	+|15b|**A**ngular **A**cceleration|AA|QAA|CAA| | ✓|degrees per second squared|Increments of 10 degrees per second squared
	155	+|15c|**A**ngular **D**eceleration|AD|QAD|CAD| | ✓|degrees per second squared|Increments of 10 degrees per second squared
	156	+|15d|**M**otion **C**ontrol|MC|QMC| | | ✓|none|MC0 to disable motion control, MC1 to enable. Session specific
	157	+| 16|**LED** Color| LED| QLED| CLED| ✓| ✓| none (integer from 1 to 8)|0=OFF 1=RED 2=GREEN 3= BLUE 4=YELLOW 5=CYAN 6=MAGENTA, 7=WHITE
	158	+| 17|**ID** #| | QID| CID| | ✓| none (integer from 0 to 250)|Note: ID 254 is a "broadcast" which all servos respond to
	159	+| 18|**B**aud rate| B| QB| CB| | ✓| none (integer)|
	160	+| 19|**G**yre direction (**G**)| G| QG| CG| ✓| ✓| none | Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)
	161	+| 20|**F**irst Position (**P**ulse)| | QFP|CFP | ✓| ✓| none |
	162	+| 21|**F**irst Position (**D**egrees)| | QFD|CFD| ✓| ✓| none |
	163	+| 22|**T**arget (**D**egree) **P**osition| | QDT| | | ✓| tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|
	164	+| 23|**M**odel **String**| | QMS| | | | none (string)| Recommended to determine the model|
	165	+| 23b|**M**odel| | QM| | | | none (integer)| Returns a raw value representing the three model inputs (36 bit)|
	166	+| 24|Serial **N**umber| | QN| | | | none (integer)|
	167	+| 25|**F**irmware version| | QF| | | | none (integer)|
	168	+| 26|**Q**uery (general status)| | Q| | | ✓| none (integer from 1 to 8)| See command description for details
	169	+| 27|**V**oltage| | QV| | | ✓| millivolts (ex 5936 = 5936mV = 5.936V)|
	170	+| 28|**T**emperature| | QT| | | ✓| tenths of degrees Celsius|Max temp before error: 85°C (servo goes limp)
	171	+| 29|**C**urrent| | QC| | | ✓| milliamps (ex 200 = 0.2A)|
	172	+| 30|**RC** Mode| | |CRC| |✓|none|(((
	173	+CRC: Add modifier "1" for RC-position mode.
	174	+CRC: Add modifier "2" for RC-wheel mode.
	175	+Any other value for the modifier results in staying in smart mode.
	176	+Puts the servo into RC mode. To revert to smart mode, use the button menu.
142	142	)))
143		-| 8|[[Position in **P**ulse>>||anchor="H8.PositioninPulse28P29"]]| P| QP| | | ✓|microseconds|(% style="width:510px" %)(((
144		-Inherited from SSC-32 serial protocol
145		-)))|(% style="text-align:center; width:113px" %)
146		-| 9|[[Position in **D**egrees>>||anchor="H9.PositioninDegrees28D29"]]| D| QD| | | ✓|tenths of degrees |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
147		-| 10|[[**W**heel mode in **D**egrees>>||anchor="H10.WheelModeinDegrees28WD29"]]| WD| QWD| | | ✓|tenths of degrees per second (ex 248 = 24.8 degrees per second)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
148		-| 11|[[**W**heel mode in **R**PM>>||anchor="H11.WheelModeinRPM28WR29"]]| WR| QWR| | | ✓|revolutions per minute (rpm)|(% style="width:510px" %)A.K.A. "Speed mode" or "Continuous rotation"|(% style="text-align:center; width:113px" %)
149		-| 12|[[Max **S**peed in **D**egrees>>||anchor="H12.SpeedinDegrees28SD29"]]| SD| QSD|CSD| ✓| ✓|tenths of degrees per second |(% style="width:510px" %)(((
150		-QSD: Add modifier "2" for instantaneous speed.
	178	+|31|**RESET**| | | | | ✓|none|Soft reset. See command for details.
	179	+|32|**DEFAULT**| | | | |✓|none|Revert to firmware default values. See command for details
	180	+|33|**UPDATE**| | | | |✓|none|Update firmware. See command for details.
151	151
152		-SD overwrites SR / CSD overwrites CSR and vice-versa.
153		-)))|(% style="text-align:center; width:113px" %)Max per servo
154		-| 13|[[Max **S**peed in **R**PM>>||anchor="H13.SpeedinRPM28SR29"]]| SR| QSR|CSR| ✓| ✓|revolutions per minute (rpm)|(% style="width:510px" %)(((
155		-QSR: Add modifier "2" for instantaneous speed
156		-
157		-SR overwrites SD / CSR overwrites CSD and vice-versa.
158		-)))|(% style="text-align:center; width:113px" %)Max per servo
159		-| 16|[[**LED** Color>>||anchor="H16.RGBLED28LED29"]]| LED| QLED| CLED| ✓| ✓|none (integer from 0 to 8)|(% style="width:510px" %)0=Off (black); 1=Red 2=Green; 3=Blue; 4=Yellow; 5=Cyan; 6=Magenta; 7=White;|(% style="text-align:center; width:113px" %)7
160		-| 17|[[**ID** #>>||anchor="H17.IdentificationNumber"]]| | QID| CID| | ✓|none (integer from 0 to 250)|(% style="width:510px" %)Note: ID 254 is a "broadcast" which all servos respond to|(% style="text-align:center; width:113px" %)0
161		-| 18|[[**B**aud rate>>||anchor="H18.BaudRate"]]| B| QB| CB| | ✓|none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)9600
162		-| 19|[[**G**yre direction (**G**)>>||anchor="H19.GyreRotationDirection"]]| G| QG| CG| ✓| ✓|none |(% style="width:510px" %)Gyre / rotation direction where 1= CW (clockwise) -1 = CCW (counter-clockwise)|(% style="text-align:center; width:113px" %)1
163		-| 20|[[**F**irst Position (**P**ulse)>>||anchor="H20.First2InitialPosition28pulse29"]]| | QFP|CFP | ✓| ✓|none |(% style="width:510px" %)CFP overwrites CFD and vice-versa|(% style="text-align:center; width:113px" %)(((
164		-Limp
165		-)))
166		-| 21|[[**F**irst Position (**D**egrees)>>||anchor="H21.First2InitialPosition28Degrees29"]]| | QFD|CFD| ✓| ✓|none |(% style="width:510px" %)CFD overwrites CFP and vice-versa|(% style="text-align:center; width:113px" %)Limp
167		-| 22|[[**T**arget (**D**egree) **P**osition>>||anchor="H22.QueryTargetPositioninDegrees28QDT29"]]| | QDT| | | ✓|tenths of degrees (ex 325 = 32.5 degrees; 91 = 9.1 degrees)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
168		-| 23|[[**M**odel **S**tring>>||anchor="H23.QueryModelString28QMS29"]]| | QMS| | | |none (string)|(% style="width:510px" %) Returns the type of servo (ST, HS, HT)|(% style="text-align:center; width:113px" %)
169		-| 24|[[Serial **N**umber>>||anchor="H24.QuerySerialNumber28QN29"]]| | QN| | | |none (integer)|(% style="width:510px" %) Returns the unique serial number for that servo|(% style="text-align:center; width:113px" %)
170		-| 25|[[**F**irmware version>>||anchor="H25.QueryFirmware28QF29"]]| | QF| | | |none (integer)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
171		-| 26|[[**Q**uery (general status)>>||anchor="H26.QueryStatus28Q29"]]| | Q| | | ✓|none (integer from 1 to 8)|(% style="width:510px" %) See command description for details|(% style="text-align:center; width:113px" %)
172		-| 27|[[**V**oltage>>||anchor="H27.QueryVoltage28QV29"]]| | QV| | | ✓|millivolts (ex 5936 = 5936mV = 5.936V)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
173		-| 28|[[**T**emperature>>||anchor="H28.QueryTemperature28QT29"]]| | QT| | | ✓|tenths of degrees Celsius|(% style="width:510px" %)Max temp before error: 85°C (servo goes limp)|(% style="text-align:center; width:113px" %)
174		-| 29|[[**C**urrent>>||anchor="H29.QueryCurrent28QC29"]]| | QC| | | ✓|milliamps (ex 200 = 0.2A)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
175		-| 30a|[[**RC** Mode>>||anchor="H30.RCMode28CRC29"]] - Position| | |CRC1| | ✓|none|(% style="width:510px" %)(((
176		-Puts the servo into RC mode. To revert to smart mode, use the button menu.
177		-)))|(% style="text-align:center; width:113px" %)Serial
178		-| 30b|[[**RC** Mode>>||anchor="H30.RCMode28CRC29"]] - Wheel| | |CRC2| | ✓| |(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
179		-| 31|[[**RESET**>>||anchor="H31.RESET"]]| | | | | ✓|none|(% style="width:510px" %)Soft reset. See command for details.|(% style="text-align:center; width:113px" %)
180		-| 32|[[**DEFAULT**>>||anchor="H32.DEFAULTA026CONFIRM"]]| | | | |✓|none|(% style="width:510px" %)Revert to firmware default values. See command for details|(% style="text-align:center; width:113px" %)
181		-| 33|[[**UPDATE**>>||anchor="H33.UPDATEA026CONFIRM"]]| | | | |✓|none|(% style="width:510px" %)Update firmware. See command for details.|(% style="text-align:center; width:113px" %)
182		-
183		-== Advanced ==
184		-
185		-|= #|=Description|= Action|= Query|= Config|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
186		-| A1|[[**A**ngular **S**tiffness>>||anchor="H14.AngularStiffness28AS29"]]| AS|QAS|CAS| ✓| ✓|none (integer -4 to +4)|(% style="width:510px" %)Suggested values are between 0 to +4|(% style="text-align:center; width:113px" %)0
187		-| A2|[[**A**ngular **H**olding Stiffness>>||anchor="H15.AngularHoldStiffness28AH29"]]|AH|QAH|CAH| | ✓|none (integer -10 to +10)|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)1
188		-| A3|[[**A**ngular **A**cceleration>>||anchor="H15b:AngularAcceleration28AA29"]]|AA|QAA|CAA| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared|(% style="text-align:center; width:113px" %)
189		-| A4|[[**A**ngular **D**eceleration>>||anchor="H15c:AngularDeceleration28AD29"]]|AD|QAD|CAD| | ✓|degrees per second squared|(% style="width:510px" %)Increments of 10 degrees per second squared|(% style="text-align:center; width:113px" %)
190		-| A5|[[**E**nable **M**otion Control>>||anchor="H15d:MotionControl28MC29"]]|EM|QEM| | | ✓|none|(% style="width:510px" %)EM0 to disable motion control, EM1 to enable|(% style="text-align:center; width:113px" %)
191		-| A6|[[**C**onfigure **L**ED **B**linking>>||anchor="H16b.ConfigureLEDBlinking28CLB29"]]| | | CLB| ✓| |none (integer from 0 to 63)|(% style="width:510px" %)(((
192		-0=No blinking, 63=Always blink;
193		-
194		-Blink while: 1=Limp; 2=Holding 4=Accel; 8=Decel; 16=Free 32=Travel;
195		-)))|(% style="text-align:center; width:113px" %)
196		-
197	197	== Details ==
198	198
199		-====== __1. Limp (**L**)__ ======
	184	+===== __1. Limp (**L**)__ =====
200	200
201	201	Example: #5L<cr>
202	202
203	203	This action causes the servo to go "limp". The microcontroller will still be powered, but the motor will not. As an emergency safety feature, should the robot not be doing what it is supposed to or risks damage, use the broadcast ID to set all servos limp #254L<cr>.
204	204
205		-====== __2. Halt & Hold (**H**)__ ======
	190	+__2. Halt & Hold (**H**)__
206	206
207	207	Example: #5H<cr>
208	208
209		-This action overrides whatever the servo might be doing at the time the command is received (accelerating, moving continuously etc.) and causes it to stop immediately and hold that angular position.
	194	+This action overrides whatever the servo might be doing at the time the command is received (accelerating, moving continuously etc.) and causes it to stop immediately and hold that position.
210	210
211		-====== __3. Timed move (**T**)__ ======
	196	+__3. Timed move (**T**)__
212	212
213	213	Example: #5P1500T2500<cr>
214	214
215		-Timed move can be used only as a modifier for a position (P, D, MD) actions. The units are in milliseconds, so a timed move of 2500 milliseconds would cause the servo to rotate from its current position to the desired position in 2.5 seconds. The onboard controller will attempt to ensure that the move is performed entirely at the desired velocity, though differences in torque may cause it to not be exact. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.
	200	+Timed move can be used only as a modifier for a position (P) action. The units are in milliseconds, so a timed move of 2500 milliseconds would cause the servo to rotate from its current position to the desired position in 2.5 seconds. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.
216	216
217		-Note: If the calculated speed at which a servo must rotate for a timed move is greater than its maximum speed (which depends on voltage and load), then it will move at its maximum speed, and the time of the move may be longer than requested.
	202	+__4. Speed (**S**)__
218	218
219		-====== __4. Speed (**S**)__ ======
220		-
221	221	Example: #5P1500S750<cr>
222	222
223	223	This command is a modifier only for a position (P) action and determines the speed of the move in microseconds per second. A speed of 750 microseconds would cause the servo to rotate from its current position to the desired position at a speed of 750 microseconds per second. This command is in place to ensure backwards compatibility with the SSC-32 / 32U protocol.
224	224
225		-====== __5. (Relative) Move in Degrees (**MD**)__ ======
	208	+__5. (Relative) Move in Degrees (**MD**)__
226	226
227	227	Example: #5MD123<cr>
228	228
229	229	The relative move command causes the servo to read its current position and move the specified number of tenths of degrees in the corresponding position. For example if the servo is set to rotate CW (default) and an MD command of 123 is sent to the servo, it will cause the servo to rotate clockwise by 12.3 degrees. Negative commands would cause the servo to rotate in the opposite configured direction.
230	230
231		-====== __6. Origin Offset Action (**O**)__ ======
	214	+__6. Origin Offset Action (**O**)__
232	232
233	233	Example: #5O2400<cr>
234	234
235		-This command allows you to temporarily change the origin of the servo in relation to the factory zero position for that session. As with all action commands, the setting will be lost upon servo reset / power cycle. Origin offset commands are not cumulative and always relate to factory zero. In the first image, the origin at factory offset '0' (centered).
	218	+This command allows you to temporarily change the origin of the servo in relation to the factory zero position. The setting will be lost upon servo reset / power cycle. Origin offset commands are not cumulative and always relate to factory zero. Note that for a given session, the O command overrides the CO command. In the first image, the origin at factory offset '0' (centered).
236	236
237	237	[[image:LSS-servo-default.jpg]]
238	238
239		-In the second image, the origin, and the corresponding angular range (explained below) have been shifted by +240.0 degrees:
	222	+In the second image, the origina, as well as the angular range (explained below) have been shifted by 240.0 degrees:
240	240
241	241	[[image:LSS-servo-origin.jpg]]
242	242
...	...	@@ -244,39 +244,39 @@
244	244
245	245	Example: #5QO<cr> Returns: *5QO-13
246	246
247		-This allows you to query the angle (in tenths of degrees) of the origin in relation to the factory zero position. In this example, the new origin is at -1.3 degrees from the factory zero.
	230	+This allows you to query the angle (in tenths of degrees) of the origin in relation to the factory zero position.
248	248
249	249	Configure Origin Offset (**CO**)
250	250
251	251	Example: #5CO-24<cr>
252	252
253		-This command allows you to change the origin of the servo in relation to the factory zero position in EEPROM. The setting will be saved upon servo reset / power cycle. Origin offset configuration commands are not cumulative and always relate to factory zero. The new origin is also used in RC mode. In the example, the new origin will be at -2.4 degrees from the factory zero.
	236	+This command allows you to change the origin of the servo in relation to the factory zero position in EEPROM. The setting will be saved upon servo reset / power cycle. Origin offset configuration commands are not cumulative and always relate to factory zero. The new origin is also used in RC mode.
254	254
255		-====== __7. Angular Range (**AR**)__ ======
	238	+__7. Angular Range (**AR**)__
256	256
257	257	Example: #5AR1800<cr>
258	258
259		-This command allows you to temporarily change the total angular range of the servo in tenths of degrees. This applies to the Position in Pulse (P) command and RC mode. The default for (P) and RC mode is 1800 (180.0 degrees total, or ±90.0 degrees). The image below shows a standard -180.0 to +180.0 range, with no offset:
	242	+This command allows you to temporarily change the total angular range of the servo in tenths of degrees. This applies to the Position in Pulse (P) command and RC mode. The default for (P) and RC mode is 1800 (180.0 degrees total, or ±90.0 degrees). In the first image,
260	260
261	261	[[image:LSS-servo-default.jpg]]
262	262
263		-Below, the angular range is restricted to 180.0 degrees, or -90.0 to +90.0. The center has remained unchanged.
	246	+Here, the angular range has been restricted to 180.0 degrees, or -90.0 to +90.0. The center has remained unchanged.
264	264
265	265	[[image:LSS-servo-ar.jpg]]
266	266
267		-Finally, the angular range action command (ex. #5AR1800<cr>) and origin offset action command (ex. #5O-1200<cr>) are used to move both the center and limit the angular range:
	250	+The angular range action command (ex. #5AR1800<cr>) and origin offset action command (ex. #5O-1200<cr>) an be used to move both the center and limit the angular range:
268	268
269	269	[[image:LSS-servo-ar-o-1.jpg]]
270	270
271	271	Query Angular Range (**QAR**)
272	272
273		-Example: #5QAR<cr> might return *5AR1800, indicating the total angular range is 180.0 degrees.
	256	+Example: #5QAR<cr> might return *5AR2756
274	274
275	275	Configure Angular Range (**CAR**)
276	276
277	277	This command allows you to change the total angular range of the servo in tenths of degrees in EEPROM. The setting will be saved upon servo reset / power cycle.
278	278
279		-====== __8. Position in Pulse (**P**)__ ======
	262	+__8. Position in Pulse (**P**)__
280	280
281	281	Example: #5P2334<cr>
282	282
...	...	@@ -289,7 +289,7 @@
289	289	This command queries the current angular position in PWM "units". The user must take into consideration that the response includes any angular range and origin configurations in order to determine the actual angle.
290	290	Valid values for QP are {-500, [500, 2500], -2500}. Values outside the [500, 2500] range are given a negative corresponding end point value to indicate they are out of bounds (note that if the servo is physically located at one of the endpoints, it may return a negative number if it is a fraction of a degree beyond the position).
291	291
292		-====== __9. Position in Degrees (**D**)__ ======
	275	+__9. Position in Degrees (**D**)__
293	293
294	294	Example: #5PD1456<cr>
295	295
...	...	@@ -303,7 +303,7 @@
303	303
304	304	This means the servo is located at 13.2 degrees.
305	305
306		-====== __10. Wheel Mode in Degrees (**WD**)__ ======
	289	+__10. Wheel Mode in Degrees (**WD**)__
307	307
308	308	Ex: #5WD900<cr>
309	309
...	...	@@ -315,7 +315,7 @@
315	315
316	316	The servo replies with the angular speed in tenths of degrees per second. A negative sign would indicate the opposite direction (for factory default a negative value would be counter clockwise).
317	317
318		-====== __11. Wheel Mode in RPM (**WR**)__ ======
	301	+__11. Wheel Mode in RPM (**WR**)__
319	319
320	320	Ex: #5WR40<cr>
321	321
...	...	@@ -327,7 +327,7 @@
327	327
328	328	The servo replies with the angular speed in rpm. A negative sign would indicate the opposite direction (for factory default a negative value would be counter clockwise).
329	329
330		-====== __12. Speed in Degrees (**SD**)__ ======
	313	+__12. Speed in Degrees (**SD**)__
331	331
332	332	Ex: #5SD1800<cr>
333	333
...	...	@@ -352,7 +352,7 @@
352	352
353	353	Using the CSD command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 180.0 degrees per second. When the servo is powered on (or after a reset), the CSD value is used. Note that CSD and CSR (described below) are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
354	354
355		-====== __13. Speed in RPM (**SR**)__ ======
	338	+__13. Speed in RPM (**SR**)__
356	356
357	357	Ex: #5SD45<cr>
358	358
...	...	@@ -377,7 +377,7 @@
377	377
378	378	Using the CSR command sets the servo's maximum speed which is saved in EEPROM. In the example above, the servo's maximum speed will be set to 45rpm. When the servo is powered on (or after a reset), the CSR value is used. Note that CSD and CSR are effectively the same, but allow the user to specify the speed in either unit. The last command (either CSR or CSD) is what the servo uses for that session.
379	379
380		-====== __14. Angular Stiffness (**AS**)__ ======
	363	+__14. Angular Stiffness (**AS**)__
381	381
382	382	The servo's rigidity / angular stiffness can be thought of as (though not identical to) a damped spring in which the value affects the stiffness and embodies how much, and how quickly the servo tried keep the requested position against changes.
383	383
...	...	@@ -405,7 +405,7 @@
405	405
406	406	Writes the desired angular stiffness value to memory.
407	407
408		-====== __15. Angular Hold Stiffness (**AH**)__ ======
	391	+__15. Angular Hold Stiffness (**AH**)__
409	409
410	410	The angular holding stiffness determines the servo's ability to hold a desired position under load. Values can be from -10 to 10, with the default being 0. Note that negative values mean the final position can be easily deflected.
411	411
...	...	@@ -425,19 +425,19 @@
425	425
426	426	This writes the angular holding stiffness of servo #5 to 2 to EEPROM
427	427
428		-====== __15b: Angular Acceleration (**AA**)__ ======
	411	+__15b: Angular Acceleration (**AA**)__
429	429
430	430	{More details to come}
431	431
432		-====== __15c: Angular Deceleration (**AD**)__ ======
	415	+__15c: Angular Deceleration (**AD**)__
433	433
434	434	{More details to come}
435	435
436		-====== __15d: Motion Control (**EM**)__ ======
	419	+__15d: Motion Control (**MC**)__
437	437
438	438	{More details to come}
439	439
440		-====== __16. RGB LED (**LED**)__ ======
	423	+__16. RGB LED (**LED**)__
441	441
442	442	Ex: #5LED3<cr>
443	443
...	...	@@ -455,22 +455,8 @@
455	455
456	456	Configuring the LED color via the CLED command sets the startup color of the servo after a reset or power cycle. Note that it also changes the session's LED color immediately as well.
457	457
458		-====== __16b. Configure LED Blinking (**CLB**)__ ======
	441	+__17. Identification Number__
459	459
460		-This command allows you to control when the RGB LED will blink the user set color (see [[16. RGB LED>>||anchor="H16.RGBLED28LED29"]] for details).
461		-You can turn on or off blinking for various LSS status. Here is the list and their associated value: 0=No blinking, ; 63=Always blink; Blink while: 1=Limp; 2=Holding 4=Accel; 8=Decel; 16=Free 32=Travel;
462		-
463		-To set blinking, use CLB with the value of your choosing. To activate blinking in multiple status, simply add together the values of the corresponding status. See examples below:
464		-
465		-Ex: #5CLB0<cr> to turn off all blinking (LED always solid)
466		-Ex: #5CLB1<cr> only blink when limp
467		-Ex: #5CLB2<cr> only blink when holding
468		-Ex: #5CLB12<cr> only blink when accel or decel
469		-Ex: #5CLB48<cr> only blink when free or travel
470		-Ex: #5CLB63<cr> blink in all status
471		-
472		-====== __17. Identification Number__ ======
473		-
474	474	A servo's identification number cannot be set "on the fly" and must be configured via the CID command described below. The factory default ID number for all servos is 0. Since smart servos are intended to be daisy chained, in order to respond differently from one another, the user must set different identification numbers. Servos with the same ID and baud rate will all receive and react to the same commands.
475	475
476	476	Query Identification (**QID**)
...	...	@@ -485,7 +485,7 @@
485	485
486	486	Setting a servo's ID in EEPROM is done via the CID command. All servos connected to the same serial bus will be assigned that ID. In most situations each servo must be set a unique ID, which means each servo must be connected individually to the serial bus and receive a unique CID number. It is best to do this before the servos are added to an assembly. Numbered stickers are provided to distinguish each servo after their ID is set, though you are free to use whatever alternative method you like.
487	487
488		-====== __18. Baud Rate__ ======
	457	+__18. Baud Rate__
489	489
490	490	A servo's baud rate cannot be set "on the fly" and must be configured via the CB command described below. The factory default baud rate for all servos is 9600. Since smart servos are intended to be daisy chained, in order to respond to the same serial bus, all servos in that project should ideally be set to the same baud rate. Setting different baud rates will have the servos respond differently and may create issues. Available baud rates are: 9.6 kbps, 19.2 kbps, 38.4 kbps, 57.6 kbps, 115.2 kbps, 230.4 kbps, 250.0 kbps, 460.8 kbps, 500.0 kbps, 750.0 kbps*, 921.6 kbps*. Servos are shipped with a baud rate set to 9600. The baud rates are currently restricted to those above.
491	491	\*: Current tests reveal baud rates above 500 kbps are unstable and can cause timeouts. Please keep this in mind if using those / testing them out.
...	...	@@ -498,13 +498,11 @@
498	498
499	499	Configure Baud Rate (**CB**)
500	500
501		-Important Note: the servo's current session retains the given baud rate and the new baud rate will only be in place when the servo is power cycled.
502		-
503	503	Ex: #5CB9600<cr>
504	504
505	505	Sending this command will change the baud rate associated with servo ID 5 to 9600 bits per second.
506	506
507		-====== __19. Gyre Rotation Direction__ ======
	474	+__19. Gyre Rotation Direction__
508	508
509	509	"Gyre" is defined as a circular course or motion. The effect of changing the gyre direction is as if you were to use a mirror image of a circle. CW = 1; CCW = -1. The factory default is clockwise (CW).
510	510
...	...	@@ -522,7 +522,7 @@
522	522
523	523	This changes the gyre direction as described above and also writes to EEPROM.
524	524
525		-====== __20. First / Initial Position (pulse)__ ======
	492	+__20. First / Initial Position (pulse)__
526	526
527	527	In certain cases, a user might want to have the servo move to a specific angle upon power up. We refer to this as "first position". The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
528	528
...	...	@@ -538,7 +538,7 @@
538	538
539	539	This configuration command means the servo, when set to RC mode, will immediately move to an angle equivalent to having received an RC pulse of 1550 microseconds upon power up. Sending a CFP command without a number results in the servo remaining limp upon power up (i.e. disabled).
540	540
541		-====== __21. First / Initial Position (Degrees)__ ======
	508	+__21. First / Initial Position (Degrees)__
542	542
543	543	In certain cases, a user might want to have the servo move to a specific angle upon power up. We refer to this as "first position". The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
544	544
...	...	@@ -554,37 +554,37 @@
554	554
555	555	This configuration command means the servo, when set to smart mode, will immediately move to 6.4 degrees upon power up. Sending a CFD command without a number results in the servo remaining limp upon power up.
556	556
557		-====== __22. Query Target Position in Degrees (**QDT**)__ ======
	524	+__22. Query Target Position in Degrees (**QDT**)__
558	558
559	559	Ex: #5QDT<cr> might return *5QDT6783<cr>
560	560
561	561	The query target position command returns the target angle during and after an action which results in a rotation of the servo horn. In the example above, the servo is rotating to a virtual position of 678.3 degrees. Should the servo not have a target position or be in wheel mode, it will respond without a number (Ex: *5QDT<cr>).
562	562
563		-====== __23. Query Model String (**QMS**)__ ======
	530	+__23. Query Model String (**QMS**)__
564	564
565	565	Ex: #5QMS<cr> might return *5QMSLSS-HS1cr>
566	566
567	567	This reply means the servo model is LSS-HS1, meaning a high speed servo, first revision.
568	568
569		-====== __23b. Query Model (**QM**)__ ======
	536	+__23b. Query Model (**QM**)__
570	570
571	571	Ex: #5QM<cr> might return *5QM68702699520cr>
572	572
573	573	This reply means the servo model is 0xFFF000000 or 100, meaning a high speed servo, first revision.
574	574
575		-====== __24. Query Serial Number (**QN**)__ ======
	542	+__24. Query Serial Number (**QN**)__
576	576
577	577	Ex: #5QN<cr> might return *5QN~_~_<cr>
578	578
579	579	The number in the response is the servo's serial number which is set and cannot be changed.
580	580
581		-====== __25. Query Firmware (**QF**)__ ======
	548	+__25. Query Firmware (**QF**)__
582	582
583	583	Ex: #5QF<cr> might return *5QF11<cr>
584	584
585	585	The integer in the reply represents the firmware version with one decimal, in this example being 1.1
586	586
587		-====== __26. Query Status (**Q**)__ ======
	554	+__26. Query Status (**Q**)__
588	588
589	589	Ex: #5Q<cr> might return *5Q6<cr>, which indicates the motor is holding a position.
590	590
...	...	@@ -594,32 +594,32 @@
594	594	|ex: *5Q2<cr>|Free moving|Motor driving circuit is not powered and horn can be moved freely
595	595	|ex: *5Q3<cr>|Accelerating|Increasing speed from rest (or previous speeD) towards travel speed
596	596	|ex: *5Q4<cr>|Traveling|Moving at a stable speed
597		-|ex: *5Q5<cr>|Decelerating|Decreasing from travel speed towards final position.
	564	+|ex: *5Q5<cr>|Deccelerating|Decreasing speed towards travel speed towards rest
598	598	|ex: *5Q6<cr>|Holding|Keeping current position
599	599	|ex: *5Q7<cr>|Stepping|Special low speed mode to maintain torque
600		-|ex: *5Q8<cr>|Outside limits|{More details coming soon}
	567	+|ex: *5Q8<cr>|Outside limits|More details coming soon
601	601	|ex: *5Q9<cr>|Stuck|Motor cannot perform request movement at current speed setting
602		-|ex: *5Q10<cr>|Blocked|Similar to stuck, but the motor is at maximum duty and still cannot move (i.e.: stalled)
	569	+|ex: *5Q10<cr>|Blocked|Similar to stuck, but the motor is at maxiumum duty and still cannot move (i.e.: stalled)
603	603
604		-====== __27. Query Voltage (**QV**)__ ======
	571	+__27. Query Voltage (**QV**)__
605	605
606	606	Ex: #5QV<cr> might return *5QV11200<cr>
607	607
608	608	The number returned has one decimal, so in the case above, servo with ID 5 has an input voltage of 11.2V (perhaps a three cell LiPo battery).
609	609
610		-====== __28. Query Temperature (**QT**)__ ======
	577	+__28. Query Temperature (**QT**)__
611	611
612	612	Ex: #5QT<cr> might return *5QT564<cr>
613	613
614	614	The units are in tenths of degrees Celcius, so in the example above, the servo's internal temperature is 56.4 degrees C. To convert from degrees Celcius to degrees Farenheit, multiply by 1.8 and add 32. Therefore 56.4C = 133.52F.
615	615
616		-====== __29. Query Current (**QC**)__ ======
	583	+__29. Query Current (**QC**)__
617	617
618	618	Ex: #5QC<cr> might return *5QC140<cr>
619	619
620	620	The units are in milliamps, so in the example above, the servo is consuming 140mA, or 0.14A.
621	621
622		-====== __30. RC Mode (**CRC**)__ ======
	589	+__30. RC Mode (**CRC**)__
623	623
624	624	This command puts the servo into RC mode (position or continuous), where it will only respond to RC pulses. Note that because this is the case, the servo will no longer accept serial commands. The servo can be placed back into smart mode by using the button menu.
625	625
...	...	@@ -631,13 +631,13 @@
631	631
632	632	EX: #5CRC<cr>
633	633
634		-====== __31. RESET__ ======
	601	+__31. RESET__
635	635
636	636	Ex: #5RESET<cr> or #5RS<cr>
637	637
638	638	This command does a "soft reset" (no power cycle required) and reverts all commands to those stored in EEPROM (i.e. configuration commands).
639	639
640		-====== __32. DEFAULT & CONFIRM__ ======
	607	+__32. DEFAULT & CONFIRM__
641	641
642	642	Ex: #5DEFAULT<cr>
643	643
...	...	@@ -649,7 +649,7 @@
649	649
650	650	Note that after the CONFIRM command is sent, the servo will automatically perform a RESET.
651	651
652		-====== __33. UPDATE & CONFIRM__ ======
	619	+__33. UPDATE & CONFIRM__
653	653
654	654	Ex: #5UPDATE<cr>
655	655

XWiki.XWikiRights[0]

Allow/Deny

...	...	@@ -1,1 +1,0 @@
1		-1

Groups

...	...	@@ -1,1 +1,0 @@
1		-xwiki:XWiki.XWikiAdminGroup

Levels

...	...	@@ -1,1 +1,0 @@
1		-view

XWiki.XWikiRights[1]

Allow/Deny

...	...	@@ -1,1 +1,0 @@
1		-1

Groups

...	...	@@ -1,1 +1,0 @@
1		-XWiki.XWikiAdminGroup

Levels

...	...	@@ -1,1 +1,0 @@
1		-view

XWiki.XWikiRights[2]

Allow/Deny

...	...	@@ -1,1 +1,0 @@
1		-1

Groups

...	...	@@ -1,1 +1,0 @@
1		-XWiki.Profiles (Lynxmotion).BETA Testers

Levels

...	...	@@ -1,1 +1,0 @@
1		-view