Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,5 +1,5 @@
1	1	(% class="wikigeneratedid" id="HTableofContents" %)
2		-**Table of Contents**
	2	+**Page Contents**
3	3
4	4	{{toc depth="3"/}}
5	5
...	...	@@ -128,6 +128,8 @@
128	128
129	129	= Command List =
130	130
	131	+== Regular ==
	132	+
131	131	|= #|=Description|= Action|= Query|= Config|=Session|= RC|= Serial|= Units|=(% style="width: 510px;" %) Notes|=(% style="width: 113px;" %)Default Value
132	132	| 1|[[**L**imp>>||anchor="H1.Limp28L29"]]| L| | | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
133	133	| 2|[[**H**alt & **H**old>>||anchor="H2.Halt26Hold28H29"]]| H| | | | | ✓|none|(% style="width:510px" %) |(% style="text-align:center; width:113px" %)
...	...	@@ -456,7 +456,7 @@
456	456
457	457	====== __18. First Position (Pulse) (**FP**)__ ======
458	458
459		-In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only.
	461	+In certain cases, a user might want to have the servo move to a specific angle upon power up; we refer to this as "first position" (a.k.a. "initial position"). The factory default has no first position value stored in EEPROM and therefore upon power up, the servo remains limp until a position (or hold command) is assigned. FP and FD are different in that FP is used for RC mode only, whereas FD is used for smart mode only. If a first position pulse is assigned, the servo will move to that angle and hold there for up to 2 seconds before going limp should a new pulse not be received.
460	460
461	461	Query First Position in Pulses (**QFP**)
462	462
...	...	@@ -552,8 +552,10 @@
552	552
553	553	EX: #5CRC2<cr>
554	554
555		-This command would place the servo in RC wheel mode after a RESET or power cycle. Note that after a RESET or power cycle, the servo will be in RC mode and will not reply to serial commands.
	557	+This command would place the servo in RC wheel mode after a RESET or power cycle. Note that after a RESET or power cycle, the servo will be in RC mode and will not reply to serial commands.
556	556
	559	+Important note:** **To revert from RC mode back to serial mode, the [[LSS - Button Menu>>doc:Lynxmotion Smart Servo (LSS).LSS - Button Menu.WebHome]] is required. Should the button be inaccessible (or broken) when the servo is in RC mode and the user needs to change to serial mode, a 5V constant HIGH needs to be sent to the servo's Rx pin (RC PWM pin), ensuring a common GND and wait for 30 seconds. Normal RC PWM pulses should not exceed 2500 milliseconds. After 30 seconds, the servo will interpret this as a desired mode change and change to serial mode. This has been implemented as a fail safe.
	560	+
557	557	====== __28. **RESET**__ ======
558	558
559	559	Ex: #5RESET<cr> or #5RS<cr>