Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -43,7 +43,7 @@
43	43
44	44	{{lightbox image="lynxmotion-smart-servo.lss-configuration-software.WebHome@lss-config-20.7.14.2-scan-options.png" title="LSS Config - 20.7.14.2 - Scan options" width="124"/}}
45	45
46		-The next step once the COM port has been selected is to scan the port. The software can send commands to (and listen for a reply from) all servo IDs (0 to 250) at all standard baud rates on the selected COM port. In the pop-up, select the baud rates which you would like to scan. You may also limit the IDs to scan for. When in doubt, leave all baud rates selected
	46	+The next step once the COM port has been selected is to scan the port. The software can send commands to (and listen for a reply from) all servo IDs (0 to 250) at all standard baud rates on the selected COM port. In the pop-up, select the baud rates which you would like to scan. You press the **ALL** button to select all baud rates, press the individual check boxes to toggle each select or press the **<<** button to select only the corresponding baud rate, deselecting all others. You may also limit the IDs to scan for. When in doubt, leave all baud rates selected.
47	47
48	48	Once you press OK, the scan will start by turning off the LED of all servos on the selected baud rates (#254LED0\r). Then, each selected baud rate is scanned for servos. The command line interface will include messages for all servos found (or not found) at each baud rate, as well as any conflicts discovered (two or more LSS at the same location). In this case, a location is defined as a baud rate and ID pair.
49	49
...	...	@@ -81,15 +81,16 @@
81	81
82	82	The firmware update option is a popup which includes:
83	83
84		-* Firmware version in dropdown format, including the current recommended version
85		-* Experimental firmware (if available)
	84	+* Firmware version selection in a dropdown list, including the current recommended version
	85	+* Experimental firmware (optional)
86	86	* Cancel firmware update
87	87	* OK to continue firmware update
88		-* Notes regarding the firmware
	88	+* Checkbox to try to save & restore the settings (config)
	89	+* Notes regarding the selected firmware
89	89
90		-The LSS Config software serves as the main software used to update the servo's onboard firmware / programming. An internet connection is needed in order for the software to check if an online update is available. The servo's current firmware version is displayed to the left of the FIRMWARE button. Pressing the button will open a popup window which allows you to select the firmware version to upload to the servo. When checked, the Exp. button will allow experimental versions of the firmware to be displayed in the list. It also allows to load directly from a local file.
	91	+The LSS Config serves as the main software used to update the servo's onboard firmware. An internet connection is needed in order for the software to check if an online update is available and obtain a copy. When checked, the Exp. button will allow experimental versions of the firmware to be displayed in the list. It also allows to load a firmware directly from a local file.
91	91
92		-Following this pop-up your servo will be restarted and a progress bar will be displayed in the command line. Do not disconnect the servo during a firmware update. If the process does get interrupted, you can still upload firmware to the LSS by going into bootloader mode by holding the button at power up.
	93	+Following this pop-up your servo will be restarted (unless already in bootloader mode, see LSS-None above) and a progress bar will be displayed in the command line. Do not disconnect the servo during a firmware update. If the process does get interrupted, you can still upload firmware to the LSS by going into bootloader mode by holding the button at power up.
93	93
94	94	__**NOTE: Before assembling the servos as part of a robot, check to see if there is a firmware update available.**__
95	95