Changes for page 03 - Wiring

Last modified by Eric Nantel on 2022/10/03 14:42
From version < 7.1 >
edited by Eric Nantel
on 2021/11/19 07:13
To version < 8.1
edited by Eric Nantel
on 2022/10/03 14:42
<
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,9 +1,9 @@
1 -{{stepNavigation previousStepURL="https://www.robotshop.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-electronics/" nextStepURL="https://www.robotshop.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-frame-lid/" pageTitle="A4WD3 Mecanum - Wiring"/}}
1 +{{stepNavigation previousStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-electronics/" nextStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-frame-lid/" pageTitle="A4WD3 Mecanum - Wiring"/}}
2 2  
3 3  (% style="width:710px" %)
4 4  |(% colspan="2" style="text-align:center" %)**Microcontroller / Independent**
5 5  |(% colspan="2" %)Two dual channel Sabertooth motor controllers are needed because each motor is connected to its own channel and can be controlled independently. Normally the encoders are connected to the microcontroller to measure angular speed and estimate distance traveled. Connections between microcontroller and the Sabertooth controller and encoders depend on the microcontroller chosen.
6 -|(% colspan="2" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/ROVER-A4WD3-Wiring-Diagrams-Mecanum.png"/}}
6 +|(% colspan="2" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/ROVER-A4WD3-Wiring-Diagrams-Mecanum.png"/}}
7 7  
8 8  {{warningBox warningText="CAUTION: Before powering the motors, ensure they rotate in the same direction on each side. If the wiring between the motors and the Sabertooth was done correctly, the motors on each side of the robot should rotate in the same direction.<br><br>If the front and rear motors rotate in opposite directions however, the track which connects them will cause them to stall and burn very quickly! If you are at all uncertain, it is safest to remove the sprockets and test the motors. If they rotate in opposite directions, the wiring to the Sabertooth needs to be corrected.
9 9  "/}}
... ... @@ -10,7 +10,7 @@
10 10  
11 11  (% style="width:710px" %)
12 12  |(% colspan="3" style="text-align:center" %)**Sabertooth 2 x 12A**
13 -|(% colspan="1" rowspan="8" style="width:350px" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/Sabertooth-2x12-PinOut.png"/}}|(% style="width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Positive Input (6-24V / 30V Absolute Max)
13 +|(% colspan="1" rowspan="8" style="width:350px" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/Sabertooth-2x12-PinOut.png"/}}|(% style="width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Positive Input (6-24V / 30V Absolute Max)
14 14  |[[image:[email protected]]]|(% style="vertical-align:middle" %)Negative Input / GND
15 15  |[[image:[email protected]]]|(% style="vertical-align:middle" %)M1A / M2A Outputs
16 16  |[[image:[email protected]]]|(% style="vertical-align:middle" %)M1B / M2B Outputs
... ... @@ -25,8 +25,8 @@
25 25  )))
26 26  
27 27  (% style="width:710px" %)
28 -|(% colspan="3" style="text-align:center" %)**Gear Motor (36GP-555-27-EN)**
29 -|(% colspan="1" rowspan="6" style="width:350px" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/36GP-555-27-EN-Wiring.PNG"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]||alt="SQUARE-Red.png"]]|Motor Positive
28 +|(% colspan="3" style="text-align:center" %)**Gear Motor (36GP 540-51-EN)**
29 +|(% colspan="1" rowspan="6" style="width:350px" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/36GP-555-27-EN-Wiring.PNG"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]||alt="SQUARE-Red.png"]]|Motor Positive
30 30  |[[image:[email protected]||alt="SQUARE-Black.png"]]|Motor Negative
31 31  |[[image:[email protected]||alt="SQUARE-Yellow.png"]]|Encoder Negative / GND
32 32  |[[image:[email protected]||alt="SQUARE-White.png"]]|Encoder Positive (5V)
... ... @@ -36,7 +36,7 @@
36 36  
37 37  (% style="width:710px" %)
38 38  |(% colspan="3" style="text-align:center" %)**RC Receiver (RadioLink R8EF)**
39 -|(% colspan="1" rowspan="7" style="width:350px" %){{lightbox image="https://www.robotshop.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/R8EF-PinOut.PNG"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Positive Input & Distribution (5-6V)
39 +|(% colspan="1" rowspan="7" style="width:350px" %){{lightbox image="https://wiki.lynxmotion.com/info/wiki/lynxmotion/download/rover-kits/a4wd3-wheeled/a4wd3-wheeled-quickstart/a4wd3-wheeled-wiring/WebHome/R8EF-PinOut.PNG"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Positive Input & Distribution (5-6V)
40 40  |(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Negative Input / GND & Distribution
41 41  |(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)Channel #1 (SBUS Optional)
42 42  |(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-White.png"]]|(% style="vertical-align:middle" %)Channel #2 (PPM Optional)
... ... @@ -44,4 +44,4 @@
44 44  |(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Gray.png"]]|(% style="vertical-align:middle" %)Channel #4
45 45  |(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Green.png"]]|(% style="vertical-align:middle" %)Channel #5
46 46  
47 -{{stepNavigation previousStepURL="https://www.robotshop.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-electronics/" nextStepURL="https://www.robotshop.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-frame-lid/" pageTitle="A4WD3 Mecanum - Wiring"/}}
47 +{{stepNavigation previousStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-electronics/" nextStepURL="https://wiki.lynxmotion.com/info/wiki/lynxmotion/view/rover-kits/a4wd3-mecanum/a4wd3-mecanum-quickstart/a4wd3-mecanum-frame-lid/" pageTitle="A4WD3 Mecanum - Wiring"/}}
Copyright RobotShop 2018