Wiki source code of LSS-5VR Board
Last modified by Eric Nantel on 2023/03/15 07:59
Hide last authors
3.1 | 1 | {{lightbox image="LSS-5VR.PNG" width="350"/}} | |
2.2 | 2 | ||
35.1 | 3 | [[[[image:[email protected]||alt="buy-online.jpg"]]>>https://www.robotshop.com/products/lynxmotion-lss-5v-2a-regulator-board-w-usb||rel="noopener noreferrer" target="_blank"]] | |
16.1 | 4 | ||
15.1 | 5 | **Table of Contents** | |
6 | |||
7 | {{toc/}} | ||
8 | |||
2.2 | 9 | = Description = | |
10 | |||
31.1 | 11 | The Lynxmotion LSS 5VR ("Lynxmotion Smart Servo to 5 Volt Regulator") module provides a regulated output of 5V at up to 2A from a 6.5V to 12.6V input via the LSS Bus. The board was conceived to be similar to a "Battery Elimination Circuit", or "BEC", as well as being used to power external 5V devices such as RC servos, sensors and/or USB powered devices. The LSS-5VR can be used with an LSS-2IO to power and control RC servos. | |
2.2 | 12 | ||
27.2 | 13 | Note that the board does not include any circuitry for detecting or charging devices via USB, and does not meet USB 2.0 / 3.0 or other power switch requirements or standards. | |
27.1 | 14 | ||
2.2 | 15 | = Features = | |
16 | |||
26.1 | 17 | * Type A USB female connector (5V power output, no data) | |
25.1 | 18 | * 2x LSS connectors allow for daisy chaining | |
19 | * 2x three row pins (NC / 5V / GND) | ||
26.1 | 20 | * Buck converter (up to 95% efficient) | |
25.1 | 21 | * Vin (6.5V - 12.6V) LED | |
26.1 | 22 | * 5V output status LED | |
23 | * Lynxmotion Smart Servo (LSS) mounting pattern | ||
24 | * Same form factor as the LSS - Power Hub and similar modules. | ||
2.2 | 25 | ||
26 | = Specifications = | ||
27 | |||
22.12 | 28 | * Based on the [[TS30042 buck converter>>https://semtech.my.salesforce.com/sfc/p/#E0000000JelG/a/44000000MCKn/3e48v2lP4vpbRsfOboAxhxdut0jxr3IIftfBJdJulOE]] | |
23.3 | 29 | * 5V output (5.3V unloaded) | |
26.1 | 30 | * Maximum output current: 2 Amps continuous / total | |
2.2 | 31 | ||
32 | = Pinout = | ||
33 | |||
34 | |(% colspan="3" style="width:350px" %)((( | ||
35 | (% class="wikigeneratedid" id="HExternalPins26Connectors" %) | ||
36 | **External Pins & Connectors** | ||
37 | ))) | ||
23.6 | 38 | |(% rowspan="6" style="width:300px" %){{lightbox image="LSS-5VR-Pinout.png"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Vin**: Input voltage supplied by LSS bus (6.5V-12.6V). Refer to LSS Voltage rating in [[LSS - Specifications>>doc:lynxmotion-smart-servo.lss-specifications.WebHome]]. Red LED indicates a voltage input Vin. | |
25.1 | 39 | |(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**Ground (G)**: Common ground. | |
23.6 | 40 | |(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Blue.png"]]|(% style="vertical-align:middle" %)**Vout**: 5V/2A output voltage (5.3V unloaded). Green LED indicates a 5V output Vout. | |
25.1 | 41 | |(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**LSS Rx** | |
42 | |(% style="vertical-align:middle" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)**LSS Tx** | ||
2.2 | 43 | |(% style="vertical-align:middle" %)[[image:[email protected]||alt="SQUARE-Red.png"]]|(% style="vertical-align:middle" %)((( | |
25.1 | 44 | **USB**: 5V (5.3V unloaded), up to 2A. Power only (no data connection). | |
2.2 | 45 | ))) | |
46 | |||
14.1 | 47 | = (% style="color:inherit; font-family:inherit" %)Dimensions & Mounting(%%) = | |
2.2 | 48 | ||
22.1 | 49 | |(% style="width:300px" %){{lightbox image="LSS-5VR-Dimensions.png"/}}|(% style="width:300px" %)[[image:servo-erector-set-system.ses-electronics.ses-modules.lss-2io-board.WebHome@LSS-2IO-Mounting.gif]]| |