Changes for page LSS-2MC Board

Last modified by Eric Nantel on 2023/05/29 07:33
From version < 40.1 >
edited by Eric Nantel
on 2021/04/07 13:53
To version < 41.1 >
edited by Eric Nantel
on 2021/04/07 14:32
< >
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -66,15 +66,11 @@
66 66  |(% style="vertical-align:middle; width:35px" %)[[image:[email protected]||alt="SQUARE-Red.png"]]|(% style="vertical-align:middle" %)(((
67 67  **USB: **Connecting only the USB will only provide voltage to the logic. It won't power Vout rail nor LSS connected on the bus.
68 68  )))
69 +|(% colspan="3" style="width:300px" %)~*~*NOTE:~*~* USB and Vin power source are isolated and there are no issues connecting both a USB and a powered LSS bus at the same time
69 69  
70 -{{warningBox warningText="**NOTE:** USB and Vin power source are isolated and there are no issues connecting both a USB and a powered LSS bus at the same time"/}}
71 +
71 71  
72 -
73 -
74 -
75 -
76 -
77 -|(% colspan="2" %)
73 +|(% colspan="2" %)**Sample Wiring / Use**
78 78  |{{lightbox image="LSS-2MC-Power-LSS-ADA.PNG"/}}|{{lightbox image="LSS-2MC-Power-LSS-HUB.PNG"/}}
79 79  |(% style="text-align:center" %)//LSS-2MC Powered by an LSS-ADA //|(% style="text-align:center" %)//LSS-2MC Powered by an LSS-HUB //
80 80  
... ... @@ -84,20 +84,26 @@
84 84  
85 85  == DC Motor Driver ==
86 86  
87 -(% style="margin-right:auto" %)
88 -|(% style="text-align:left; width:300px" %) |(% style="text-align:left" %)
89 -|(% style="width:300px" %) |(((
90 -
91 -)))
83 +Lorren Ipsum
92 92  
93 93  |**Sample Wiring / Use**
94 94  |{{lightbox image="LSS-2MC-Wiring-DC.PNG" width="900"/}}
95 95  
96 -**Pin / ID Default Assignment**
88 +==
89 +Bipolar Stepper Driver ==
97 97  
91 +Lorren Ipsum
92 +
93 +|**Sample Wiring / Use**
94 +|{{lightbox image="LSS-2MC-Wiring-Stepper.PNG" width="900"/}}
95 +
96 +== **Pin / ID Default Assignment** ==
97 +
98 98  The following pinout is used in the sample code so as to not interfere with any other guides or manuals. This pinout can be changed in the Arduino program.
99 99  
100 -(% style="width:459px" %)
100 +== ==
101 +
102 +(% style="font-size:14px; width:459px" %)
101 101  |(% style="width:111px" %)**PIn/Device**|(% style="width:52px" %)**ID**|(% style="width:139px" %)**Middle Pin Supply**|(% style="width:135px" %)**Notes**
102 102  |(% style="width:111px" %)2IO Master ID|(% style="width:52px" %)207|(% style="width:139px" %)-|(% style="width:135px" %)RGB LED
103 103  |(% style="width:111px" %)A3|(% style="width:52px" %)203|(% style="width:139px" %)5V|(% style="width:135px" %)Analog Pin
... ... @@ -108,31 +108,6 @@
108 108  |(% style="width:111px" %)D11|(% style="width:52px" %)211|(% style="width:139px" %)Not Connected|(% style="width:135px" %)Digital Pin
109 109  |(% colspan="4" style="width:111px" %)To change the ID,s you can look at the "CID" command [[HERE>>https://www.robotshop.com/info/wiki/lynxmotion/view/servo-erector-set-system/ses-electronics/ses-modules/lss-2io-board/2io-2rc-mode-communication-protocol/#H6.IdentificationNumber28ID29]]
110 110  
111 -==
112 -Bipolar Stepper Driver ==
113 -
114 -|(% style="text-align:left; width:300px" %) |(% style="text-align:left" %)
115 -|(% style="width:300px" %) |(((
116 -
117 -)))
118 -
119 -|**Sample Wiring / Use**
120 -|{{lightbox image="LSS-2MC-Wiring-Stepper.PNG" width="900"/}}
121 -
122 -== Arduino ==
123 -
124 -|(% style="text-align:left; width:300px" %) |(% style="text-align:left" %)
125 -|(% style="width:300px" %) |(((
126 -
127 -)))
128 -
129 -|**Sample Wiring / Use**
130 -|
131 -
132 -= Advanced Pinout =
133 -
134 -{{lightbox image="LSS-2IO-PINOUT.png" width="700"/}}
135 -
136 136  = Dimensions & Mounting =
137 137  
138 138  |(% style="width:300px" %){{lightbox image="LSS-2IO-Dimensions.png"/}}|(% style="width:300px" %)[[image:LSS-2IO-Mounting.gif]]|
Copyright RobotShop 2018