Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -59,6 +59,8 @@
59	59	|(% colspan="2" rowspan="1" %)**Pin D2: **H-Bridge NSleep (set high to enable)
60	60	|(% colspan="2" rowspan="1" %)**Pin D8:** H-Bridge NFault
61	61
	62	+= Power Options =
	63	+
62	62	|(% colspan="3" style="width:300px" %)**Power**
63	63	|(% colspan="1" rowspan="2" style="width:300px" %){{lightbox image="LSS-2MC-Power.png"/}}|(% style="vertical-align:middle; width:35px" %)[[image:[email protected]]]|(% style="vertical-align:middle" %)(((
64	64	**LSS Connectors: **The board is meant to be powered from ONE of the two LSS connectors. Vin will supply the two on-board 5V regulators (logic and Vout) and to the Lynxmotion Smart Servos connected on the bus. Power will also be supplied to the h-bridge at the same voltage as the bus voltage.
...	...	@@ -70,10 +70,6 @@
70	70	)))
71	71	|(% colspan="3" style="width:300px" %)~*~*NOTE:~*~* USB and Vin power source are isolated and there are no issues connecting both a USB and a powered LSS bus at the same time
72	72
73		-= Wiring =
74		-
75		-== Power Options ==
76		-
77	77	|(% colspan="2" %)**Sample Wiring / Use**
78	78	|{{lightbox image="LSS-2MC-Power-LSS-ADA.png"/}}|{{lightbox image="LSS-2MC-Power-LSS-HUB.png"/}}
79	79	|(% style="text-align:center" %)(((
...	...	@@ -86,33 +86,27 @@
86	86	//Lynxmotion Smart Servo and LSS-2IO are optional //
87	87	)))
88	88
89		-== Dual Brushed DC / H-Bridge ==
	87	+= Dual H-Bridge (DC Motors) =
90	90
91		-(% class="wikigeneratedid" id="HLorrenIpsum" %)
92		-Lorren Ipsum
93		-
94	94	|**Sample Wiring / Use**
95	95	|{{lightbox image="LSS-2MC-Wiring-DC.png" width="900"/}}
96	96
97		-== Single Bipolar Stepper Motor ==
	92	+= Bipolar Stepper Motor =
98	98
99		-(% class="wikigeneratedid" id="HLorrenIpsum" %)
100		-Lorren Ipsum
101		-
102	102	|**Sample Wiring / Use**
103	103	|{{lightbox image="LSS-2MC-Wiring-Stepper.png" width="900"/}}
104	104
105		-== **Pin / ID Default Assignment** ==
	97	+(% class="wikigeneratedid" %)
	98	+= 2MC - Sample Code =
106	106
107		-The following pinout is used in the sample code so as to not interfere with any other guides or manuals. This pinout can be changed in the Arduino program.
	100	+= **Pin / ID Default Assignment** =
108	108
	102	+The following pinout is used in the sample code so as to not interfere with any other guides or manuals.
	103	+
109	109	(% style="font-size:14px; width:459px" %)
110		-|(% style="text-align:center; width:111px" %)**PIn/Device**|(% style="text-align:center; width:52px" %)**ID**|(% style="text-align:center; width:139px" %)**Middle Pin Supply**|(% style="text-align:center; width:135px" %)**Notes**
111		-|(% style="width:111px" %)2IO Master ID|(% style="width:52px" %) |(% style="width:139px" %) |(% style="width:135px" %)
112		-|(% style="width:111px" %)Stepper|(% style="width:52px" %) |(% style="width:139px" %) |(% style="width:135px" %)
113		-|(% style="width:111px" %)DC Motor 1|(% style="width:52px" %) |(% style="width:139px" %) |(% style="width:135px" %)
114		-|(% style="width:111px" %)DC Motor 2|(% style="width:52px" %) |(% style="width:139px" %) |(% style="width:135px" %)
115		-|(% style="width:111px" %)A3|(% style="width:52px" %)203|(% style="width:139px" %)5V|(% style="width:135px" %)Analog Pin
	105	+|(% style="width:111px" %)Stepper|(% style="width:52px" %)215|(% style="width:139px" %) |(% style="width:135px" %)
	106	+|(% style="width:111px" %)DC Motor 1|(% style="width:52px" %)215|(% style="width:139px" %) |(% style="width:135px" %)
	107	+|(% style="width:111px" %)DC Motor 2|(% style="width:52px" %)216|(% style="width:139px" %) |(% style="width:135px" %)
116	116	|(% colspan="4" style="width:111px" %)To change the ID,s you can look at the "CID" command [[HERE>>attach:LSS 2MC Board V0.3.pdf]]
117	117
118	118	= Schematic =