SES - Electronics
Version 46.1 by Coleman Benson on 2019/03/25 09:34
- Manage
- Copy
- Actions
- Export
- Print preview
- View Source
Export
Expand each section below to view more information:
 | SES - Chargers
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | SES - Modules The Servo Erector Set (SES) modular building system includes a variety of electronic and electro-mechanical modules. This section provides an overview of each module and links to where you can obtain user guides and more information.. Power and Communication The Lynxmotion Smart Servo (LSS) Adapter Board is an electronic board which allows for easy configuration and control of the Lynxmotion Smart Servos. The board includes a variety of features and functionality and provides power distribution via six LSS six connectors. The board is intended to be powered from a LiPo battery through the on-board male XT60 connector, or with a wall adapter with a female XT60 connector. There are many ways to interface with this board, including USB, Arduino (shield compatible), Bee socket and more . The LSS Power Hub provides a simple solution to supply power to and communicate with the smart servos. It is also a useful tool to split the LSS bus from one servo to two or three while allowing these ports to be powered separately. The adapter is meant to be mounted directly to the servos. Sensors & IO {More information to come}
SES - Modules
BotBoarduino Microcontroller (Arduino Compatible) Arduino & Shield compatible microcontroller board.
SSC-32U USB Servo Controller The SSC-32U USB servo controller is a dedicated RC servo controller with some big features. It has high resolution (1uS) for accurate positioning, and extremely smooth moves.
LSS Adapter (Type-C)
LSS Adapter (USB Mini)
LSS 2IO Board Microcontroller (Arduino Compatible)
LSS 2MC Board Microcontroller (Arduino Compatible)
LSS 5VR Board
LSS Power Hub
SSC-32 Servo Controller (DB9) The SSC-32 (serial servo controller) is a small preassembled servo controller with some big features. It has high resolution (1uS) for accurate positioning, and extremely smooth moves.
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | SES - Chargers
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 | SES - Wall Adapters The SES V2 system incorporates features to clean up cabling / wiring without restricting access. This page covers the selection of wires, corresponding accessories and proposes several wiring methods. Specifications
For more information regarding the pinout, how to connect the servos and the LSS servo's electronics, refer to the LSS - Electrical page. When purchasing Lynxmotion serial cables, the user does not need to worry about any modifications as all the pins and wires are correct, however, should the LSS be connected to non-Lynxmotion products such as a microcontroller, be certain to understand the pinout before making any connections. Wire Routing In a robotic creation, keeping the wires as clean as possible helps ensure they do not get snagged internally or externally. Many V2 brackets include slots where plastic cable clips can be installed in order to more cleanly and securely rout wires. When wiring a custom robotic creation, ensure there is enough slack in the wires to allow for the full range of motion at each joint, and so they do not get snagged. Each clip only allows passage of one 4-wire cable. Straight vs. Y Serial Cables Straight serial cables are used to daisy chain multiple LSS servos / modules one after the next. However, with a limit of 3A per cable, additional power may need to be applied and as such, a Y-harness and Power Hub are needed (change the jumper on the Power Hub). A Y-harness can also be used to daisy chain servos when one side of the servo is blocked. SES - Wiring
Lynxmotion PRO CAN / Ethernet Cable Communication cables used in the Lynxmotion PRO system
Lynxmotion PRO Power XT60 Extension Cable Power cables used in the Lynxmotion PRO system
M12 to M12 Extension Cable (6') Data and power cable used for DH Robotics two and three finger grippers
Lynxmotion USB A to Type C Data and power cable
Lynxmotion Smart Servo (LSS) - Serial Cables Lynxmotion SKU: 100mm / 150mm / 200mm 300mm LSS-C-100-S
Lynxmotion Smart Servo (LSS) - 300mm RC Cable This cable allows the LSS servos to be easily connected to a standard 3-pin RC source. The fourth connector (from the servo's Tx pin) is separate. Should additional length be needed, a standard 3-pin servo extension (male to female) cable can be used.
Lynxmotion Smart Servo (LSS) - Serial Y Cables Lynxmotion SKU: 100mm / 150mm / 200mm / 300mm LSS-C-100-Y
Plastic Cable Clip Clip intended to be mounted to SES V2 brackets to help with wire routing. Magnets are meant to attach external shells.
Magnets for the Cable Clip Small magnet used
Extra Long Stacking Headers These extra long stacking headers are intended to be use with the LSS Adapter and fit through the board. They are used to stack a shield above the LSS adapter and onto a shield compatible microcontroller.
Lynxmotion USB A to Mini B
Lynxmotion USB A to Type C
Power Harness XT60 to XT30
Lynxmotion PRO CAN / Ethernet Cable Communication cables used in the Lynxmotion PRO system
Lynxmotion PRO Power XT60 Extension Cable Power cables used in the Lynxmotion PRO system
M12 to M12 Extension Cable (6') Data and power cable used for DH Robotics two and three finger grippers
Lynxmotion USB A to Type C Data and power cable
Lynxmotion Smart Servo (LSS) - Serial Cables Lynxmotion SKU: 100mm / 150mm / 200mm 300mm LSS-C-100-S
Lynxmotion Smart Servo (LSS) - 300mm RC Cable This cable allows the LSS servos to be easily connected to a standard 3-pin RC source. The fourth connector (from the servo's Tx pin) is separate. Should additional length be needed, a standard 3-pin servo extension (male to female) cable can be used.
Lynxmotion Smart Servo (LSS) - Serial Y Cables Lynxmotion SKU: 100mm / 150mm / 200mm / 300mm LSS-C-100-Y
Plastic Cable Clip Clip intended to be mounted to SES V2 brackets to help with wire routing. Magnets are meant to attach external shells.
Magnets for the Cable Clip Small magnet used
Extra Long Stacking Headers These extra long stacking headers are intended to be use with the LSS Adapter and fit through the board. They are used to stack a shield above the LSS adapter and onto a shield compatible microcontroller.
Lynxmotion USB A to Mini B
Lynxmotion USB A to Type C
Power Harness XT60 to XT30
{{/showhide} | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Tags:
Created by Eric Nantel on 2019/03/21 11:17